A 6 kg lance 3 m long lance is balanced about an unknown pivot. A 2...

A 6 kg lance 3 m long lance is balanced about an unknown pivot. A 2 kg pennant hangs 30 cm from one end. The point
of the lance weighs 1 kg. Draw a rigid body diagram for the lance and find where you should put your finger so that the
lance balances.

Now the lance is pivoted about its center. If a reasonably smart knight applies a force to the NON-sharp end of the lance
at an angle of 30 degrees relative to the horizontal, what force must they apply to keep the lance from rotating?

Expert Solution

genius_generous answered 2 years ago

a 3 m long beam with a mass of 35 is balanced horizontally on a fulcrum...

a 3 m long beam with a mass of 35 is balanced horizontally on a fulcrum (pivot) while a person stands at one end of the beam. the position of the fulcrum is .65 m from the end of the beam where the person is standing. what is the mass of the person?

A 3 kg ball is attached to a tree branch by a 2.0 m long rope....

A 3 kg ball is attached to a tree branch by a 2.0 m long rope. It is released from rest when the string is parallel to the ground. Just at it swings to its lowest point, it collides elastically head-on with a 2 kg ball of the same dimension, but going in the opposite direction. The 3 kg ball rebounds at a speed of 13 m/s after the collision. Find the speed of the 2 kg ball before the...

Four asteroids, of mass M = 3 × 10^6 kg, are positioned at the corners of...

Four asteroids, of mass M = 3 × 10^6 kg, are positioned at the corners of an imaginary square of side length s = 2.4 × 10^8 m. Two other asteroids of mass m = 2 × 10^6 kg are positioned in the middle of the left and right sides of the square. Mass of spaceship is 2000kg. If a spaceship is positioned at the middle of the bottom side of the square what is the net force on the...

E2-6 (Algo) Finding Unknown Values in the Cost of Goods Manufactured Report [LO 2-3, 2-6]...

E2-6 (Algo) Finding Unknown Values in the Cost of Goods Manufactured Report [LO 2-3, 2-6] Mulligan Manufacturing Company uses a job order cost system with overhead applied to products at a rate of 150 percent of direct labor cost. Required: Treating each case independently, selected from the manufacturing data given below, find the missing amounts. You should do them in the order listed. (Hint: For the manufacturing costs in Case 3, first solve for conversion costs and then determine...

The person’s mass, m= 68.1 kg, the unknown drag coefficient is, c , with units kg/s,...

The person’s mass, m= 68.1 kg, the unknown drag coefficient is, c , with units kg/s, and the local acceleration of gravity is g= 9.80 m/s2 . Our model for the person’s velocity vs time gave us a linear differential equation whose analytical solution was the following: V(t) = g*m/c*[1-exp(-c/m*t)]. Your job is to find “c”. You need to use the MATLAB “help” documentation to find the nonlinear curve fitting function and syntax for how to use it. Hint you...

E2-6 Finding Unknown Values in the Cost of Goods Manufactured Report [LO 2-3, 2-6] Mulligan Manufacturing...

E2-6 Finding Unknown Values in the Cost of Goods Manufactured Report [LO 2-3, 2-6] Mulligan Manufacturing Company uses a job order cost system with overhead applied to products at a rate of 150 percent of direct labor cost. Required: Treating each case independently, selected from the manufacturing data given below, find the missing amounts. You should do them in the order listed. (Hint: For the manufacturing costs in Case 3, first solve for conversion costs and then determine how much...

The thin uniform rod in the figure has length 5.0 m and can pivot about a...

The thin uniform rod in the figure has length 5.0 m and can pivot about a horizontal, frictionless pin through one end. It is released from rest at angle θ = 50° above the horizontal. Use the principle of conservation of energy to determine the angular speed of the rod as it passes through the horizontal position. Assume free-fall acceleration to be equal to 9.83 m/s2.

A 1.71 kg ball and a 3.27 kg ball are connected by a 1.76 m long...

A 1.71 kg ball and a 3.27 kg ball are connected by a 1.76 m long rigid, massless rod. The rod is rotating clockwise about its center of mass at 24 rpm. What torque will bring the balls to a halt in 10.06 s? (Give an absolute value of torque.)

Given the following balanced equation Ca3P2 + 6 H2O ----> 3 Ca(OH) + 2 PH3. a)...

Given the following balanced equation Ca3P2 + 6 H2O ----> 3 Ca(OH) + 2 PH3. a) What is the theoretical yield (in grams) of PH3 produced from 125g each of Ca3P2 and H2O? b) What is the limiting reagent? c) What is the percent yield if only 38.9g of PH3 are produced?

(a) A 60 kg person, is in a room that is 6 meters long. Can this...

(a) A 60 kg person, is in a room that is 6 meters long. Can this person be certain that they is not moving, even if to all appearances they are sitting perfectly still? If not, then estimate within what range their velocity is likely to be (you may assume that their average speed is zero). (b) Find the size of the smallest one-dimensional box in which you can confine an electron, in order to be sure that the speed...

Question