Question

In: Mechanical Engineering

A Four bar mechanism with a frame length of 200 mm, crank length of 100 mm,...

A Four bar mechanism with a frame length of 200 mm, crank length of 100 mm, coupler length of 300 mm and follower length of 250 mm, if the mechanism is assembled in open cpen configuration and the input angle is 45o .

what is:

1-The coupler angle for open and crossed  configuration ?

2-The output angle for open and crossed configuration ?

Solutions

Expert Solution


Related Solutions

Thermal properties A bar has an initial length of 100 mm at room temperature of 27oC....
Thermal properties A bar has an initial length of 100 mm at room temperature of 27oC. The tensile test indicates that the bar yields when it reaches is the stress level of 145 MPa and the strain value of 2.071 x 10-3. The bar is later placed in an oven and heated from room temperature to 100 oC. The linear coefficient of thermal expansion of the material is 23 x 10-6 oC-1 at 27oC, and 34 x 10-6 oC-1 at...
When length the of crank and connecting rod is changed (i.e crank of length is changed...
When length the of crank and connecting rod is changed (i.e crank of length is changed by keeping connecting rod length constant and in other case connecting rod length is changed by keeping the crank length constant) what implications does it have on the reciprocating engine?
in a crank and slotted lever quick return mechanism, as shown in figure the driving crank...
in a crank and slotted lever quick return mechanism, as shown in figure the driving crank length is 75mm. the distance between the fixed centres is 200mm and the length of the slotted lever is 500mm. find the ratio of the times taken on the cutting and idle strokes. determine the effective stroke also
Hydraulic excavators always have a 4-bar linkage between the inverted crank-slider mechanism and the bucket. Find...
Hydraulic excavators always have a 4-bar linkage between the inverted crank-slider mechanism and the bucket. Find a picture from which you can determine if this 4-bar linkage is a triple rocker, a double crank, a double rocker, or a crank-rocke
What are the inversions of four bar mechanism &give their applications ?What are the inversions of...
What are the inversions of four bar mechanism &give their applications ?What are the inversions of four bar mechanism &give their applications ?
Saturated steam condenses at the surface of a 200 mm pipe with the length of 2...
Saturated steam condenses at the surface of a 200 mm pipe with the length of 2 m and temperature of 90 C. Find the rate of heat transfer and total condensation rate if the pressure is atmospheric. B)The bottom of a copper pan, 100 mm in diameter, is maintained at 109°C by the heating element of an electric range. Estimate the power required to boil the water in this pan. Determine the evaporation rate. What is the ratio of the...
A microscope with a tube length of 200 mm achieves a total magnification of 400
A microscope with a tube length of 200 mm achieves a total magnification of 400
Water is flowing through a pipe having the diameter 200 mm and 100 mm at sections...
Water is flowing through a pipe having the diameter 200 mm and 100 mm at sections 1 and 2 respectively. The rate of flow through the pipe is 35 liters per second. The section 1 is 6000 mm and section 2 is 4000 mm above the datum line. If the pressure at the section 1 is 0.4 N/mm2, find the intensity of pressure at section 2.                                                            
A square frame made of 4 mm-thick iron rods and an edge length of 1 m...
A square frame made of 4 mm-thick iron rods and an edge length of 1 m is pushed into a homogeneous magnetic field of B=2 T (T=Vs/m^2) with a constant speed of 15 m/s. Assuming the frame is initially at room temperature (20°C). a) Why does the frame heat up? b)What is the temperature of the frame right after the experiment? c) Now you pull it out of the B-field with the same constant speed, what is the temperature of...
A steel ruler (100 mm) is used for measuring the length of a block. The ambient...
A steel ruler (100 mm) is used for measuring the length of a block. The ambient temperature is found likely to vary in between 24 °C and 25 °C. The temperature is likely to be anywhere within these limits. The temperature variation follows square distribution, with expected value to be 24.5 °C. Determine the degree of uncertainty that will be registered when measurement is done using steel scale? CTE = 11.5 x 10-6 / °C
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT