Water is flowing through a pipe having the diameter 200 mm and 100 mm at sections...

Water is flowing through a pipe having the diameter 200 mm and 100 mm at sections 1 and 2 respectively. The rate of flow through the pipe is 35 liters per second. The section 1 is 6000 mm and section 2 is 4000 mm above the datum line. If the pressure at the section 1 is 0.4 N/mm², find the intensity of pressure at section 2.

Expert Solution

samet mamat answered 1 month ago

A water is flowing through a circular varying diameter pipe. The water completely fills the pipe...

A water is flowing through a circular varying diameter pipe. The water completely fills the pipe at all its sections. 1- What is the water velocity of the water at the first section if you know that the diameter of the pipe at this section= 22 cm and the water is flowing at a rate of 2.5 m3/s? 2- What is the diameter of the pipe at the second section if you know that the water velocity at this section...

Consider a pipe (diameter of 50 mm) with air flowing through it. The inlet conditions are:...

Consider a pipe (diameter of 50 mm) with air flowing through it. The inlet conditions are: Mach 3; total pressure = 1000 kPa and 550 K. The friction coefficient (f) is 0.004. The exit Mach number decreases with the length of the pipe. Assume adiabatic, steady flow. Write a short Matlab code and plot the following, while the exit Mach number changes from 2.5 to 0.99 with increments of ?M=0.01. Find the length of the pipe that is going to...

Water flows through a cast iron pipe with a diameter of 30 mm. The pipe is...

Water flows through a cast iron pipe with a diameter of 30 mm. The pipe is inclined at an angle of 3 degrees from horizontal and is 40 m long. The water flows due to gravity only. What is the maximum volume flow rate of the water? You may ignore any minor loses.

1)10 m3 /h of water flows through a pipe with 100 mm inside diameter. Calculate the...

1)10 m3 /h of water flows through a pipe with 100 mm inside diameter. Calculate the flow velocity inside this pipe. ? 2) A river discharges 100 m3 of water to the sea every 2 seconds. What is the flow-rate of this river expressed in m3/s?

A pipe, 900 m long and 200 mm in diameter discharges water to the atmosphere at...

A pipe, 900 m long and 200 mm in diameter discharges water to the atmosphere at a point 10 m below the inlet level. With an inlet pressure of 40 kPa gauge, the flow rate is 40 litres/sec. At a point half way between the pipe inlet and outlet, a new tapping is made from which water is taken at a rate of 18 litres/sec. To what value must the inlet pressure be raised in order to maintain the same...

Crude oil of specific gravity (0.75) is flowing through a pipe. The pipe has a diameter...

Crude oil of specific gravity (0.75) is flowing through a pipe. The pipe has a diameter of 100 mm and 50 mm at the sections 1 and 2 respectively. The velocity of crude oil at the section 1 is 550 cm/s. The section 1 is 3000 mm and section 2 is 2000 mm above the datum. If the pressure at the section 1 is 0.2 N/mm2, find the intensity of pressure at section 2?

) A 50 mm-diameter propeller was installed in a 150 mm-diameter water pipe and the propeller...

) A 50 mm-diameter propeller was installed in a 150 mm-diameter water pipe and the propeller speed was measured for a range of water discharge in the pipe. The water had a density and dynamic viscosity of 1000 kg/m3 and 0.00112 Ns/m2 respectively. The measured results were as follows: Q (litres/s): 12 28 45 63 95 120 160 180 N (rps): 5 10 15 20 30 40 60 80 Plot the dependence of propeller coefficient against propeller Reynolds number. A...

Two water reservoirs are joined by a sharp ended flexible pipe 100 mm in diameter and...

Two water reservoirs are joined by a sharp ended flexible pipe 100 mm in diameter and 36 m long. The ends of the pipe differ in level by 4 m. The surface level of the upper reservoir is 1.8 m above the pipe inlet whilst that of the lower reservoir is 1.2 m above the pipe outlet. At a position 7.5 m horizontally from the upper reservoir, the pipe is required to pass over a barrier. Assuming that the pipe...

Water is flowing in the pipe shown in the figure below, with the 7.70-cm diameter at...

Water is flowing in the pipe shown in the figure below, with the 7.70-cm diameter at point 1 tapering to 3.45 cm at point 2, located y = 11.5 cm below point 1. The water pressure at point 1 is 3.20 ✕ 104 Pa and decreases by 50% at point 2. Assume steady, ideal flow. What is the speed of the water at the following points? Point 1? Point 2?

(c) A 50 mm-diameter propeller was installed in a 150 mm-diameter water pipe and the propeller...

(c) A 50 mm-diameter propeller was installed in a 150 mm-diameter water pipe and the propeller speed was measured for a range of water discharge in the pipe. The water had a density and dynamic viscosity of 1000 kg/m3 and 0.00112 Ns/m2 respectively. The measured results were as follows: Q (litres/s): 12 28 45 63 95 120 160 180 N (rps): 5 10 15 20 30 40 60 80 Plot the dependence of propeller coefficient against propeller Reynolds number. A...

Question