Question

In: Electrical Engineering

Design a 4x4 Sequential Multiplier Circuit Design a sequential circuit to calculate the product of two...

Design a 4x4 Sequential Multiplier Circuit

Design a sequential circuit to calculate the product of two 4-bit binary numbers, and then display the decimal result in three HEX displays. Design the circuit at the register transfer level. The inputs include two 4-bit binary numbers, one clock signal, one reset, and one start. The output includes one 8-bit binary number, one ready signal. The sequential circuit uses adder only, and does not use combinational multiplier. Using basic gates : Counter, Register, Shift register, Adder. The design shall have two circuits: A main circuit, A controller circuit.

Solutions

Expert Solution


Related Solutions

Construct a 4x4 multiplier circuit.
Construct a 4x4 multiplier circuit.
Design a Moore sequential circuit that has an input X and an output Y. The circuit...
Design a Moore sequential circuit that has an input X and an output Y. The circuit detects the following sequence: 100 Your answer should include state diagram and state table. Hint. X= 0 1 0 1 0 0 0 1 1 1 0 0 1 0 1 Y= 0 0 0 0 0 1 0 0 0 0 0 1 0 0 0
It is required to design a synchronous sequential circuit that receives two input bit streams X...
It is required to design a synchronous sequential circuit that receives two input bit streams X and Y, and detects identical 4-bit sequences in both X and Y that are non-overlapping. The output Z is also a bit stream that produces a 1 only after detecting two identical 4-bit input sequences. Use an asynchronous reset input to reset the sequential circuit to its initial state. Example: X: 001010 110010 0111 1010100 0111 Y: 011010 100010 0111 1000100 0010 Z: 000001...
Design and implement a sequential circuit that counts from 0-3 in a repeating cycle with two...
Design and implement a sequential circuit that counts from 0-3 in a repeating cycle with two inputs: step and reset. If the step input is 1 the count progresses to the next value, if 0 you stay at the current value. If the reset input is 1 the count returns to 0, if 0 it has no effect. If both step and reset are 1, reset takes precedence. Use J-K flip flops in your design and follow the design process...
Design and implement a binary-encoded sequential circuit subject to the following specifications.   This circuit is going...
Design and implement a binary-encoded sequential circuit subject to the following specifications.   This circuit is going to be used to control access to security system. It has a single 2-bit wide input, called X = X1X0 that represents a key-pad that is capable of accepting numbers 0 to 3, representing digits of a passcode. It has a single 1-bit wide output, called F, that is attached to the disarming mechanism. The behavior is that if the correct passcode is entered...
2. A sequential circuit has two pulse inputs, x1 and x2. The output of the circuit...
2. A sequential circuit has two pulse inputs, x1 and x2. The output of the circuit becomes 1 whenever the pulse sequence x1x1x2x2x2x1 is detected. The output then remains 1 for all subsequent x1 pulses until an x2 pulse occurs. (a) Derive a minimal state table describing the circuit operation. (Here you need to define the states and then perform state reduction). (b) Synthesize the circuit using SR latches in the master rank. (Here, you need to make state assignment,...
Design a sequential circuit with 2 JK flip-flops A and B, and 2 inputs, E...
Design a sequential circuit with 2 JK flip-flops A and B, and 2 inputs, E and x. the design must adhere to the following requirements: If E = 0, the circuit remains in the same state regardless of the value of x.  When E = 1 and x = 1, the circuit goes through the state transitions from 00 to 01 to 10 to 11 back to 00 and repeats. When E = 1 and x = 0, the circuit goes through the...
Use JK-Flip-Flop to design a sequential circuit as an input for the previous designed decoder to...
Use JK-Flip-Flop to design a sequential circuit as an input for the previous designed decoder to write UAE. In this design, the sequential circuit will be used instead of the two bits switches and the output will be shown in three 7-segment displays one for each letter. Letters must glow one by one in a correct sequence where the speed depends on the clock frequency. Use only one circuit as an input for the three 7-segment displays where one of...
Design a synchronous sequential logic circuit with input X (that has been synchronized to the clock)...
Design a synchronous sequential logic circuit with input X (that has been synchronized to the clock) and output Y. Every second high-to-low transition of X results in a one clock period long pulse on Y immediately after the transition. Otherwise, Y is 0. Draw a timing diagram (showing input, output and state variables) for an appropriate sequence on input X
Implement a 4x4 multiplier using gate level (verilog code and test bench)
Implement a 4x4 multiplier using gate level (verilog code and test bench)
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT