for this set of assignment, Moore state machine

Design a sequence detector to detect "001", where 0 arrives first, then 0, then 1. You need to show the test sequences you used to confirm that your state diagram is operating correctly. When the complete "001" sequence has been detected, the output goes high. Otherwise, the output stays at zero.
Shows your state diagram, state table, encoded state table (use minimized bit encoding), logic equations, and logic circuit. (30 points)

3. Re-do (2) using one-hot encoding

An NMOS transistor has KP = 80 μA/V2, Vto = 1V, L = 4μm, and W = 100 μm. Carefully sketch to scale the drain characteristics for vDS ranging from 0 to 10V and vGS = 0.5 and 4V

Draw a high frequency small signal model for BJT and MOSFET, for common gate, common source and common drain amplifiers

. Discuss the factory lighting

In a single design, implement 3 wave generators by means of operational amplifiers: wave
square, triangle wave, sine wave.

IMPORTANT
The wave generating equipment has to be activated by means of an external AC source,
that being activated by a switch, allows the activation of the system.

SIMULATION is required in the MULTISIM Software. Attach screenshot of the entire circuit and the waves.
and also the calculations.

Prepare the calculations of each case, which support the output signal obtained by
use any of the generators.

The MULTISIM simulation of the project with the three circuits in a single diagram.

Describe the Pinch off condition in JFETs and its impact over the drain current. Draw
the N channel JFET with proper regions?

What is the smallest size conductor allowed to be used in a building for branch circuits?

What is the smallest size conductor allowed to be connected in parallel?

There are three current-carrying conductors in a raceway that is to be installed in an area with an ambient temperature of 86°F. It is necessary to

There are six current-carrying conductors in a raceway that is to be installed in an area with an ambient temperature of 96°F. It is necessary to

Describe the differences between SR latches, D latches, D flip flops, JK flip flops, and T flip flops.

Three loads are connected in parallel to an AC supply of 120∠0° V. The loads are 40∠30° Ω, 50 - j30 Ω
and 30 + j40 Ω.
a) Draw the circuit diagram
b) Determine the amplitude and phase angle of the supply current graphically by constructing a
phasor diagram using a suitable scale of the load currents and source voltage.
c) State the overall power factor using the answer from part (b).
d) Construct another phasor diagram for the system that illustrates an improved power factor to
unity.
e) Determine the VAR rating of the load required to achieve this using its current phasor determined
graphically from part (d). State its capacitance or inductance.
f) Draw the power triangles for the system before and after power factor correction.

1.Who has the authority to test ELT(emergency locater transmiter)?

2.Differences in the functions of ELTs that are set by manufacturing and the Federal Communication Commission (FCC)

please this answer.

Question (06+06+06+06 ) -

a) Examine and Identify the cause of the followings:

i) The air blast breakers are very sensitive to the rate of rise of re-striking voltage.

ii) Circuit interruption easier in an AC circuit than in a DC circuit.

iii) Surge diverters located very close to the equipment to be protected.

b) Assuming the same peak value, compare the following two surges: 1/50 usec surge and 3/50 usec surge.

Consider a Si p-n junction at T=300K with the following parameters: Na=5x1017cm-3, Nd=5x1017cm-3 Dn=25 cm2 /s D P=10 cm2 /s τn=5x10-7 s τP=5x10-7 s. Let the photocurrent density be 20 mA/cm2 . (a) Calculate the maximum power delivered to the load assuming that the fill factor is 0.8. (b) By what factor will the output power increase from (a) if the solar intensity is increase by a factor of 10 due to light concentration. Comment on your results

types of induction type Instruments, full explanations

Question No 2

a) Draw functional block diagrams of a typical sensor system and a typical actuator
system. ( 10 marks)

b) Draw hierarchy of an Industrial Automation system_ Briefly describe function of each
level ( 15 marks)