10) For the Rosemount 3051C Transmitter a) Would it fit into a 1ftx1ftx1ft box? b) Would it fit in a 6inx6inx6in box? c) What does a “starred” option represent? d) What are the various pressure ranges that can be selected. e) For isolating Diaphragms 2, 3, 4 and 7, what kind of materials can be handled by the sensor?

9) Look up the Rosemount 3051 Pressure Transmitter. a) What is the difference between the Differential Pressure and Absolute Pressure measurement? b) What is the difference between Gage and Absolute pressure? c) What is the difference between the Coplanar Pressure Transmitter and the In-Line Pressure Transmitter? d) What is meant by HART Communication protocol. e) Is this transmitter approved for use with drinking water? Aboard ships? In China as intrinsically safe. f) Name all the transmitter output options.

Use SVD method to compress and decompress images in the MATLAB.

Compression function. The input is an image file and k. The output is a text file containing the reduced U, V , and the reduced diagonals of ?.

Decompression function. The input is the output of the compression code. The output is an image (you can use imshow for this purpose).

question#1: List and describe various features of electronic systems.

question#2: List and discuss the steps in designing an embedded system.

Note: please type the answer. if you cannot type, then don't answer

A 1000MVA, 20kV, 60 Hz three phase generator is connected to an infinite bus through a 1000MVA, 20kV? / 345kVY transformer to a 345kV circuit breaker and a 345kV transmission line. The generator reactances are X``d=0.17, X`d=0.30, and Xd=1.5 per unit on a 1000MVA, 20kV base. Generator time constants are T``d=0.05 seconds, T`d=1.0 seconds, and TA=0.10 seconds. The transformer series reactance is 0.10 per unit on the transformer ratings as a base. Neglect transformer losses, excitation current, and transformer time constants. The far end of the line is considered to be an infinite bus operating at 1.0 per unit voltage on the transformer ratings as a base. The line reactance is +j0.20 per unit on the same base as everything else. A three phase short circuit occurs on the line side of the transformer when the generator operates at no load. Breakers interrupt the fault three cycles after it begins. Determine the subtransient current through the transformer in per unit and the rms asymmetrical fault current that the breakers interrupt assuming maximum dc offset.

Briefly describe how each of the following factors influences the electrical resistivity of metals: i) Temperature. ii) Solid solution alloying. iii) Existence of multiple solid phases. iv) Work hardening.

Briefly describe how each of the following factors influences the electrical resistivity of metals: i) Temperature. ii) Solid solution alloying. iii) Existence of multiple solid phases. iv) Work hardening.

Design microstrip circular array antenna in HFSS software and MATLAB CODE FOR IT.

Design microstrip circular array antenna in HFSS software and MATLAB CODE FOR IT.

IF YOU KNOW THEN ONLY DO OR ELSE LEAVE FOR OTHER

ANTENNA ,ELECTRICAL ENGINEERING

PLC projects can be quite large, and need to be very carefully thought out. If you were to be in charge of a complete PLC project, please list and DISCUSS the major areas / groupings (at least eight) would you break the project down, into

Design a clamp circuit to clamp the negative extreme of a periodic input waveform of 10 sin(100????)?? to -5V. Use 1 diode, 1 Zener diode, 1 resistor and 1 capacitor of suitable values. Assume a 0.6V forward drop for all diodes and that the Zener diodes have an ideal characteristic in the breakdown region. Power supply voltages of ±15V are available.

Write a detailed summary about the working principle of Schottky diodes, photodiodes, solar cells and light emitting diodes (LEDs). You can use any source you want, but please include your sources in the “References” section of your summary!

Write a detailed summary about the working principle of Schottky diodes, photodiodes, solar cells and light emitting diodes (LEDs). You can use any source you want, but please include your sources in the “References” section of your summary!

Please list and describe the THREE major parts of a VHDL program. Describe each of them and give an example.

Control DC Using PIC18f46k20 and MPLAB IDE v8.8, write a program that can

1. Start and Stop the motor

2.Vary The motor Speed

3.Change the direction of the motor rotation

4.Display motor speed in OLED screen

using c of MPLAB IDE v8.8

please test the code before posting

How to Design amplifier circuit that has a gain of 1000 to 1500. And apply it on multisim.