Question

In: Electrical Engineering

Using Multisim, design a 2-bit, synchronous binary counter and verify that it counts in the right...

Using Multisim, design a 2-bit, synchronous binary counter and verify that it counts in the right sequence, Can count up or down and use any FF you desire; 4 screen shots in total: 1 for each input combination

Solutions

Expert Solution

I have designed the 2-bit synchrounous Up-Down counter using D-FF.if input X=0 counter counting in up,if X=0 counter counts down.

if you are satisfied with my work,PLEASE UPVOTE.

   THANK YOU!


Related Solutions

Using JK flipflopDesign a multisim schematic for a 4 bit synchronous counter that counts numbers in...
Using JK flipflopDesign a multisim schematic for a 4 bit synchronous counter that counts numbers in Gray code. 4 bit Gray code is as follows: 0000 0001 0011 0010 0110 0111 0101 0100 1100 1101 1111 1110 1010 1001 1000
Please write in multisim: Design 3 bit a synchronous counter to produce the following sequence: 0, 1, 2, 5, 3 then 0.by using...
Please write in multisim: Design 3 bit a synchronous counter to produce the following sequence: 0, 1, 2, 5, 3 then 0.by using J-K Filp Flop.. Please i need in multisim and Step of solution. Thanks!!
Design a synchronous 3-bit binary counter that generates the repeated sequence of 0, 3, 4, 7,...
Design a synchronous 3-bit binary counter that generates the repeated sequence of 0, 3, 4, 7, 0, 3, 4, 7, 0… The outputs of the flip-flops are to be the binary output signals of your counter. Your solution needs to include the input equations for the flip-flops, and a circuit diagram for each version. a) Design the counter using D flip-flops b) Design the counter using T flip-flops c) Design the counter using JK flip-flops
Design a 5 bit binary counter on logicly?
Design a 5 bit binary counter on logicly?
Design a synchronous up down counter with the following binary sequence 1, 2, 4,5,7 using J-K...
Design a synchronous up down counter with the following binary sequence 1, 2, 4,5,7 using J-K Flip Flop
1. design a mod-16 ripple down counter using positive triggered 2. design a synchronous counter to...
1. design a mod-16 ripple down counter using positive triggered 2. design a synchronous counter to count in the following sequence : 15, 9,, 11, 5, 2, 13, 1
Design a synchronous counter of four-bit using D flip‐flops and gates (AND, OR etc.) *use verilog...
Design a synchronous counter of four-bit using D flip‐flops and gates (AND, OR etc.) *use verilog language modules and test and explain briefly
(a) Design an FSM (only state diagram and state table) for a 3-bit counter that counts...
(a) Design an FSM (only state diagram and state table) for a 3-bit counter that counts through odd numbers downwards. Assume the reset state to be the lowest value of the counter. Use an active low reset to reset the counter. (b) Write a behavioral VHDL code that implements the FSM. (c) Write a VHDL test bench to test the FSM.
1. (20pts) Design a 3-bit counter that counts from 0000 to 1111 using JK flip/flops. Do...
1. (20pts) Design a 3-bit counter that counts from 0000 to 1111 using JK flip/flops. Do not forget to include the carry to detect overflow.
design a counter that counts 0,3,2,4,1,5,7 and repeats using T-ff
design a counter that counts 0,3,2,4,1,5,7 and repeats using T-ff
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT