Question

In: Other

In a power plant based on a simple Rankine cycle, steam enters the turbine at 15...

In a power plant based on a simple Rankine cycle, steam enters the turbine at 15 MPa and 900°C. The condenser pressure is 5 kPa. The turbine operates adiabatically and has an isentropic efficiency of 85%, and the pump also operates adiabatically and has an isentropic efficiency of 80%. Determine

  1. the work required to pump the water to the boiler in kJ/kg of water flowing, and

  2. the enthalpy of the water leaving the pump.

Solutions

Expert Solution


Related Solutions

A steam power plant operates on the simple ideal rankine cycle. the steam enters the turbine...
A steam power plant operates on the simple ideal rankine cycle. the steam enters the turbine at 4 MPa and 500 C and leaves it at 50 kPa and 150 C. the water leaves the condenser as a saturated liquid and is subsequently displaced to the boiler by means of a pump at a temperature of 85 C, which is the isentrophic efficiency of the turbine?
Consider a steam power plant operating on the simple ideal Rankine cycle. Steam enters the turbine...
Consider a steam power plant operating on the simple ideal Rankine cycle. Steam enters the turbine at 15 MPa and 600°C. The steam condenses in the condenser at 10 kPa. Use the EES software to study the effects of the following cases on the cycle performance and to sketch the T-s diagram for each case: Plot the variation of the cycle thermal efficiency with the turbine isentropic efficiency. Take the isentropic efficiency of the turbine in the range 70% to...
Consider a steam power plant operating on the simple ideal Rankine cycle. Steam enters the turbine...
Consider a steam power plant operating on the simple ideal Rankine cycle. Steam enters the turbine at 15 MPa and 600°C. The steam condenses in the condenser at 10 kPa. Use the EES software to study the effects of the following cases on the cycle performance and to sketch the T-s diagram for each case: #Plot the variation of the cycle thermal efficiency with the turbine isentropic efficiency. Take the isentropic efficiency of the turbine in the range 70% to...
A steam power plant operates on a practical Rankine Cycle. The steam enters the turbine at...
A steam power plant operates on a practical Rankine Cycle. The steam enters the turbine at 3 MPa and “648” K and is condensed in the condenser at a pressure of 46 kPa. You are assigned on a project to improve the thermal efficiency of this plant. a) Draw the schematic of the plant and determine the thermal efficiency of the practical cycle assuming that the efficiencies of pump and turbine are 0.75 and 0.7, respectively. ( b) Draw a...
A steam power plant operates on a regenerative Rankine cycle. Steam enters the turbine at 6...
A steam power plant operates on a regenerative Rankine cycle. Steam enters the turbine at 6 MPa at 700 ºC and the condenser at 10 kPa. Turbine has isentropic efficiency of 85% and pumps have isentropic efficiency of 90%. Steam is extracted from the turbine at 0.6 MPa to heat the feedwater in an open feedwater heater. Water leaves the open feedwater heater as saturated liquid. a) Draw the system with labels and show the ideal and the non-ideal cycle...
Consider a steam power plant operating on a simple ideal Rankine cycle in which the steam...
Consider a steam power plant operating on a simple ideal Rankine cycle in which the steam enters the turbine at 3 MPa and 350C and is condensed in the condenser at 75 kPa. Determine the thermal efficiency of this cycle and sketch an appropriately labeled T-s diagram. Also compare this thermal efficiency to that a Carnot heat engine operating between these same two limits. The change in enthalpy across the pump = work done by the pump: h2-h1= v1(P2– P1)
The net power of a steam power plant operating according to the simple ideal Rankine cycle...
The net power of a steam power plant operating according to the simple ideal Rankine cycle is 30.5 MW. Water vapor enters the turbine at 7 MPa pressure and 500 ° C, expands to 10 kPa condenser pressure in the turbine. The steam is condensed in the condenser by cooling it with water from a lake. The flow rate of the lake water is 1950 kg / h. Get the pump and turbine adiabatic efficiency of 87%. Show the cycle...
Consider a steam power plant operating on the ideal reheat Rankine cycle. Steam enters the high-pressure...
Consider a steam power plant operating on the ideal reheat Rankine cycle. Steam enters the high-pressure turbine at PH MPa and TH °C and is condensed in the condenser at a pressure of PL kPa. Assume the steam is reheated to the inlet temperature of the high-pressure turbine, and that pump work is NOT negligible. If the moisture content of the steam at the exit of the low-pressure turbine is not to exceed w% percent, determine: (a) the pressure at...
Consider a steam power plant operating on a simple ideal Rankine cycle and having a net...
Consider a steam power plant operating on a simple ideal Rankine cycle and having a net power output of 57 MW. The steam enters the turbine at 9 MPa and 575 ° C and exits at 150 ° C, then it is cooled in the condenser to a pressure of 100 kPa by means of the cooling water from a lake and that circulates through the condenser tubes to a rate of 1370 kg / s. Consider leaving the pump...
8. In a Rankine cycle steam enters the turbine at 900 psia and 1000oF and exhausts...
8. In a Rankine cycle steam enters the turbine at 900 psia and 1000oF and exhausts at 1 psia. What is the thermal efficiency? Neglect pump work. State your answer as a percent to one decimal place. Example: 25.2 9. Steam is expanded to 12% moisture at 1 psia in a Rankine cycle. If the initial pressure is 400 psia, what is the efficiency? Neglect pump work. Express your answer as a percent to one decimal place. Example: 32.5 I...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT