2 kg of iron ingot at 1100oC is mixed with 1 kg of water at -20oC....

2 kg of iron ingot at 1100^oC is mixed with 1 kg of water at -20^oC. Once the thermal equilibrium is reached, what would be the final state of water? Be as detailed as possible.

Expert Solution

genius_generous answered 6 months ago

Suppose 1.16 kg of water at 11.6 ◦C is mixed with 1.7 kg of water at...

Suppose 1.16 kg of water at 11.6 ◦C is mixed with 1.7 kg of water at 81◦C. After equilibrium is reached, the mixture has an uniform temperature of 52.8517◦C. What is the change in entropy of the system? The specific heat of water is 4186 J/kg · K. Answer in units of J/K.

How much heat energy is required to warm up 2.35 kg of water, from 20oC to...

How much heat energy is required to warm up 2.35 kg of water, from 20oC to 83oC ? Need to show unit conversion and all referents in calculation.

An adiabatic rigid container, holding water initially at 100 kPa and 20oC, receives 209kJ/kg of paddle...

An adiabatic rigid container, holding water initially at 100 kPa and 20oC, receives 209kJ/kg of paddle work. Determine the final temperature.

An iron boiler of mass 180 kg contains 730 kg of water at 11 ∘C. A...

An iron boiler of mass 180 kg contains 730 kg of water at 11 ∘C. A heater supplies energy at the rate of 58,000 kJ/h. The specific heat of iron is 450 J/kg⋅C∘, the specific heat of water is 4186 J/kg⋅C∘, the heat of vaporization of water is 2260 kJ/kg⋅C∘. Assume that before the water reaches the boiling point, all the heat energy goes into raising the temperature of the iron or the steam, and none goes to the vaporization...

Model 2 - Oxidation of Iron C) 1.00 kg iron reacts with 0.86 kg oxygen from...

Model 2 - Oxidation of Iron C) 1.00 kg iron reacts with 0.86 kg oxygen from the atmosphere to produce iron(III) oxide {aka rust}. In model C, what is the total mass of iron and oxygen in kg? Convert to your answer to grams and show how you would do this mathematical operation, and what is the maximum possible mass of iron(III) oxide product? Please explain your answer

Pressure in a storage tank is maintained at 1 MN/m2 to supply water at 20oC and...

Pressure in a storage tank is maintained at 1 MN/m2 to supply water at 20oC and atmospheric pressure through 200 m (equivalent length, including fittings) of drawn steel tubing (30 mm OD, 6 mm wall thickness). What flow rate of water can be maintained?

A 20 gram iron block at an initial temperature of 20oC is placed in 20 grams...

A 20 gram iron block at an initial temperature of 20oC is placed in 20 grams of water at an initial temperature of 80oC. Assuming no heat is lost to the surroundings, what would be the final temperature of the system once you reach thermal equilibrium? CSiron=0.449JgoC CSwater=4.18JgoC 74.2o C 80.0o C 25.8o C 50.0o C 112o C

A cast iron saucepan of mass 4.4 kg is filled with 20 L of water at...

A cast iron saucepan of mass 4.4 kg is filled with 20 L of water at 25 °C, placed on an electric hotplate, and initially brought up to boiling point. Further heat is applied until half of the water has boiled off. What is the cost of the energy used if electricity costs 30 cents per kWh and the hotplate has an efficiency of 75%?

Water at 300kPa and 20oC is heated in a chamber by mixing it with superheated steam...

Water at 300kPa and 20oC is heated in a chamber by mixing it with superheated steam at 300kPa and 300oC. The cold water enters the chamber at a rate of 1.9 kg/s. Calculate the mass flow rate of the superheated steam, if the mixture leaves the chamber at 60oC. answer is ______kg/s If necessary, define system and energy flows shown on sketch. Complete solution shown analytically before numbers.

A cooler contains 1 kg of ice at -5°C. 2 kg of water at 50°C is...

A cooler contains 1 kg of ice at -5°C. 2 kg of water at 50°C is added to the cooler. If the cooler does not exchange any heat with the rest of the world, what is the final temperature of the ice and water?

Question