Question

In: Other

A piston–cylinder device contains 5 kg of steam at 100°C with a quality of 50 percent....


A piston–cylinder device contains 5 kg of steam at 100°C with a quality of 50 percent. This steam undergoes two processes as follows: (1-2) Heat is transferred to the steam in a reversible manner while the temperature is held constant until the steam exists as a saturated vapor.(2-3) The steam expands in an adiabatic, reversible process until the pressure is 15 kPa. Sketch these processes with respect to the saturation lines on a single TS diagram and determine the heat transferred to the steam and work done by the steam.
(answer: 5641 kJ, 1291 kJ by saying "by the steam" we suggest magnitude of the work)


Solutions

Expert Solution


Related Solutions

A piston-cylinder device contains 0.56 kg of steam at 300 degrees C and 1.4 MPa. Steam...
A piston-cylinder device contains 0.56 kg of steam at 300 degrees C and 1.4 MPa. Steam is cooled at constant pressure until one-half of the mass condenses. (a) Find the final temperature. T1= _______ degrees celcius (b) Determine the volume change in m3
A piston-cylinder device initially contains 0.20(kg) of steam at 3.5(MPa), 300(C). The steam loses heat to...
A piston-cylinder device initially contains 0.20(kg) of steam at 3.5(MPa), 300(C). The steam loses heat to the surroundings and the piston moves down, hitting a set of stops at which point the cylinder contains saturated liquid water. The cooling continues until the cylinder contains water at 220C. A) Sketch the above process on a P-v chart, indicating values B) Determine the pressureand qualityof the final mixture. C) Determine the boundary work (in kJ)
A piston–cylinder device contains 0.85 kg of refrigerant-134a at -10°C. The piston that is free to...
A piston–cylinder device contains 0.85 kg of refrigerant-134a at -10°C. The piston that is free to move has a mass of 12 kg and a diameter of 25 cm. The local atmospheric pressure is 88 kPa. Now, heat is transferred to refrigerant-134a until the temperature is 10°C. Determine (a) the final pressure, (b) the change in the volume of the cylinder, and (c) the change in the enthalpy of the refrigerant-134a.
A piston–cylinder device contains steam that undergoes a reversible thermodynamic cycle. Initially the steam is at...
A piston–cylinder device contains steam that undergoes a reversible thermodynamic cycle. Initially the steam is at 400 kPa and 350oC with a volume of 0.3 m3. The steam is first expanded isothermally to 150 kPa, then compressed adiabatically to the initial pressure, and finally compressed at the constant pressure to the initial state. Determine (a) the net work and heat transfer for the cycle after you calculate the work and heat interaction for each process and (b) show the cyclic...
A piston-cylinder device contains a saturated mixture of steam and water having a total mass of...
A piston-cylinder device contains a saturated mixture of steam and water having a total mass of 0.5 kg at a pressure of 160 kPa and an initial volume of 100 liters. Heat is then added and the fluid expands at constant pressure until it reaches a saturated vapor state. a) Draw a diagram representing the process showing the initial and final states of the system. b) Sketch this process on a P-v diagram with respect to the saturation lines, critical...
A piston-cylinder device, whose piston is resting on a set of stops, initially contains 2 kg...
A piston-cylinder device, whose piston is resting on a set of stops, initially contains 2 kg of air at 300 kPa and 27ºC. The mass of the piston is such that a pressure of 600 kPa is required to move it upward. Heat is now transferred to the air until its volume doubles. a) Determine the work done by the air and b) the total heat transferred to the air during this process. c) Also, sketch the process on a...
A spring-loaded piston-cylinder device contains 0.5 kg of water initially at 90℃ and with an initial quality of 20.9%.
A spring-loaded piston-cylinder device contains 0.5 kg of water initially at 90℃ and with an initial quality of 20.9%. At its initial state, the spring is relaxed and does not exert any force on the piston. The device is now heated until the pressure is 400 kPa and the new temperature is 250℃. What is the boundary work done by the water during this process? kJ What is the total amount of heat transfer into the system? kJ BONUS: If...
Prob. 4-68 A piston–cylinder device contains 2.2 kg of nitrogen initially at 100 kPa and 25C....
Prob. 4-68 A piston–cylinder device contains 2.2 kg of nitrogen initially at 100 kPa and 25C. The nitrogen is now compressed slowly in a polytropic process during which PV^1.3 = constant until the volume is reduced by one-half. Determine the work done and the heat transfer for this process. 4–69    Reconsider Prob. 4–68. Using EES (or other) software,plot the process described in the problem on a P-V diagram, and investigate the effect of the poly- tropic exponent n on the boundary...
A piston?cylinder device initially contains 1.5?kg saturated liquid water at 120°C. Now heat is transferred to...
A piston?cylinder device initially contains 1.5?kg saturated liquid water at 120°C. Now heat is transferred to the water until the volume increases 100 times. Determine: a. Initial Volume of the water. b. Final volume of water. c. Final state of water. d. Amount of heat added to the water e. Draw the T?s diagram
Four kilograms of steam in a piston/cylinder device at 400 kPa and 175 °C undergoes isothermal...
Four kilograms of steam in a piston/cylinder device at 400 kPa and 175 °C undergoes isothermal and mechanically reversible process to a final pressure such that the steam is completely condensed (i.e., became a saturated liquid). Determine Q and W for this process: (b) Using generalized correlations and Equations (6.70 – 6.74). Comment on the accuracy of your answer. [Answer: Q = -9,461 kJ, W = 1494.9 kJ]
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT