Question

In: Other

We often use grinding in closed circuit, and have a targeted value for a circulated load....

We often use grinding in closed circuit, and have a targeted value for a circulated load. What is the formula for the percentage circulating load? Explain why a circulating load is preferable to just grinding until we are sure that everything would pass through the post grinding screen.

Solutions

Expert Solution

Circulation load is very important parameter that should be consider for grinding efficiency. Here I submit the different calculation for circulation load


Related Solutions

At my work, we often have multiple & different components from multiple suppliers that we use...
At my work, we often have multiple & different components from multiple suppliers that we use to solve it down to tubing to make IV administration sets for hospitals. Each component supplier has its own unique set of dimensions where we are to bond to the tubing. We have tried to standardize the outside diameter of the tubing so that we have universal dimensions that work for three tiers of dimensions and components. It is important to take into consideration...
Often times, we are not told to use a mean or a proportion, but we should...
Often times, we are not told to use a mean or a proportion, but we should know which is the best method for measuring our data. Explain, what type of data would it be most appropriate to use a mean and what type of data would it be most appropriate to use a proportion?
In a circuit we have a source with 75 W impedance that we want to connect...
In a circuit we have a source with 75 W impedance that we want to connect to a 300 W load with a transmission line with characteristic impedance of 75 W. To achieve maximum power transfer an inductor will be connected in series to the source. a. Use the Smith Chart on the next page to get the minimum length of the line in wavelengths and the inductor reactance value. Write down the values here. b. Use the input impedance...
In finance we often assume that the objective of the firm is to maximise the value...
In finance we often assume that the objective of the firm is to maximise the value of the firm. Why might this be a desirable objective? Why might managers not pursue such an objective?
Q1. What is Laplace transform and why do we use it in circuit analysis.
Q1. What is Laplace transform and why do we use it in circuit analysis.
(HVAC) For a specific building with a specific user, we have calculated the heating load. if...
(HVAC) For a specific building with a specific user, we have calculated the heating load. if we use deferent heat provider such as hot water,gas heaters or radiators , would it be a change in calculated heating load?? in other words Is the calculation of heating load independent of the type of heating system?
Often we would like to make the user think we like him/her so we use a...
Often we would like to make the user think we like him/her so we use a friendly prompt to get them to decide if they want to continue a loop. One can make a sentinel using an integer value outside of the expected input range but a more delightful way is to ask politely if: System.out.println("Do you want to play again?); In order to do this we will need a scanner and a do-while loop. For the scanner sometimes the...
Company spokespeople are often heard to say, "We have to be in that market". What is...
Company spokespeople are often heard to say, "We have to be in that market". What is a likely explanation for this statement if the market is (a) China; (b) Germany; (c) Brazil; (d) Japan; (e) the United States? I’m 350 words, Give examples of products or services.
In policy analysis we use triangulation in situation specific scenarios to evaluate metric options. Often we...
In policy analysis we use triangulation in situation specific scenarios to evaluate metric options. Often we have the benefit to propose a new dependent variable and by new we mean one that other researchers (to your knowledge) have not used as a “y”. You just said that to an arts major. Her face is blank. Explain what you meant in English.
We have a RLC series circuit. On this circuit V=100+j0 volts R=10ohm, L=85mH and C=1uF regarding...
We have a RLC series circuit. On this circuit V=100+j0 volts R=10ohm, L=85mH and C=1uF regarding to this values; * What should F0 has to be for making this circuit work at resonance position? * What is XL value with using F0 frequency? * What is XC value with using F0 frequency? * What is I value when the circuit is at resonance position? * What are voltages on VR, VXL, and VXC components when the circuit is on resonance...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT