In a circuit we have a source with 75 W impedance that we want to connect...

In a circuit we have a source with 75 W impedance that we want to connect to a 300 W load with a transmission line with characteristic impedance of 75 W. To achieve maximum power transfer an inductor will be connected in series to the source.

a. Use the Smith Chart on the next page to get the minimum length of the line in wavelengths and the inductor reactance value. Write down the values here.

b. Use the input impedance formula, Zin, for a lossless line to get the value of the input impedance with the length given by the Smith Chart.

c. Compare the reactance of the Smith Chart and the formula.

Expert Solution

Manojponduru answered 10 months ago

When we connect a number of light bulbs in a circuit with a battery, we can...

When we connect a number of light bulbs in a circuit with a battery, we can use our models of current, resistance, and Kirchhoff's principles to predict the relative brightness of the bulbs. If the bulbs are all identical, then the brightness of a bulb will be an indicator of the current through that bulb (i.e., a brighter bulb has more current). 1. The bulbs in the circuit shown on the right are all identical. Predict which bulb or bulbs...

Assuming a characteristic impedance of 75 Ω and a load impedance of 100Ω, ﬁnd the input...

Assuming a characteristic impedance of 75 Ω and a load impedance of 100Ω, ﬁnd the input impedance at λ/2, λ and 2λ. How each input impedance will vary for the case of: i) matched line; ii) short-circuit line; iii) open circuit line?

An amplifier with an output impedance of 75 ? is connected to a filter with a...

An amplifier with an output impedance of 75 ? is connected to a filter with a characteristic impedance of 60 – 20j ?. Design a single shunt stub matching network using an open circuit for a frequency of 500 MHz. Show ALL calculations. a) Calculate the normalized load admittance. b) Determine the distance (in ?) to the stub in the direction of the generator. c) Determine the normalized input admittance of the stub. d) Calculate the susceptance of the stub....

Suppose we have a 10-Hz sinusoidal voltage source, vin(t). Draw the diagram of a circuit that...

Suppose we have a 10-Hz sinusoidal voltage source, vin(t). Draw the diagram of a circuit that clamps the positive peaks to −4V. The circuit should be composed of ideal diodes, dc voltage sources, and other components as needed. List any constraints that should be observed in selecting component values. Be sure to label the terminals across which the clamped output waveform vo(t) appears.

How to connect Lung cancer with the following topics. We have to somehow connect lung cancer...

How to connect Lung cancer with the following topics. We have to somehow connect lung cancer with these two expectations together and write an essay. I just need some ideas. Thanks B1. analyze the effects of various human activities on the diversity of living things; B3. demonstrate an understanding of the diversity of living organisms in terms of the principles of taxonomy and phylogeny

Attach a screenshot of Multisim circuit. flip flops: D, T and JK, connect the circuit and...

Attach a screenshot of Multisim circuit. flip flops: D, T and JK, connect the circuit and verify the characteristic tables.

The total impedance of the circuit. The voltage drop across the coil. The total phase constant...

The total impedance of the circuit. The voltage drop across the coil. The total phase constant of the circuit. Calculate the frequency band width. Calculate the natural frequency.

We want to design a simple "four clock pulse" timer circuit. In addition to the clock...

We want to design a simple "four clock pulse" timer circuit. In addition to the clock input, the timer has a "Restart" input (R), three "data" outputs (ABC) which indicate the count, and one "beeper" output (D). The behavior of the circuit is as follows: Idle Mode The timer output is ABC=100 and the beeper is off (D=0) as long as R=0. If R=1 on any clock edge in this mode, the timer goes into the... Restart/Hold Mode The timer...

1. For a resistor capacitor circuit, what is the relationship between impedance and capacitive resistance? ☐...

1. For a resistor capacitor circuit, what is the relationship between impedance and capacitive resistance? ☐ Z = R2-XC2 ☐ Z = R2+XC2 ☐ Z = R-XC ☐ Z = R+XC 2. For an inductor circuit, what happens to the energy? ☐ Lost in the inductor ☐ Supplied by the inductor ☐ Zero net energy in the inductor ☐ None of these 3. What is the phase for a resistor inductor circuit? ☐ -90° ☐ +90° ☐ +45° ☐...

In a three-phase circuit the balanced delta load of (36 +j54) ohms is fed by impedance...

In a three-phase circuit the balanced delta load of (36 +j54) ohms is fed by impedance conductors (5 +j70) ohms. If the generator voltage is 120 V angle 0° phase A, calculate a) the bc voltage on the load, b) the powers in the conductors, c) the bc voltage of the delta load and d) the power delta on the load.

Question