The bottom reinforcement in a 200mm × 500mm concrete beam is found to have corroded during...

The bottom reinforcement in a 200mm × 500mm concrete beam is found to have corroded during its service life. Scans indicate that the effective diameter of the steel has reduced from 16?? ?? to 15?? ??. Determine the % reduction in the tensile capacity of the beam. The yield strength of the steel reinforcement is 500??Pa.

Please Answer Question Above

Expert Solution

Ally Wells answered 7 months ago

This question is referring to a concrete beam with steel rebar reinforcement, For a simply supported...

This question is referring to a concrete beam with steel rebar reinforcement, For a simply supported beam with width 10 inches and depth 14 inches design the steel to resist a maximum moment of 50 kip feet. span=15 feet. Concrete 4 ksi. steel is 60 ksi.

A simply supported beam has a width of 200mm and depth of 400mm is 4m long....

A simply supported beam has a width of 200mm and depth of 400mm is 4m long. It carries a uniformly distributed load of 20 kN/m over the whole beam and a point load of 40 kN at the center of the beam. Compute the maximum deflection if the maximum slope produced in the beam is 2× ??-3 radian.

2.A simply supported beam has a width of 200mm and depth of 400mm is 4m long....

2.A simply supported beam has a width of 200mm and depth of 400mm is 4m long. It carries a uniformly distributed load of 20 kN/m over the whole beam and a point load of 40 kN at the center of the beam. Compute the maximum deflection if the maximum slope produced in the beam is 2× ??-3 radian.

Performance of Reinforced Concrete Slab due to Reinforcement Corrosion

Consider a concrete beam in an interior environment as follows: a. The beam is simply supported...

Consider a concrete beam in an interior environment as follows: a. The beam is simply supported with a design span of 4.8 metres. b. The dead load in the beam is uniformly distributed. c. Dead load on the beam, in addition to its own weight, is 6.9 KN/m of which 75% is permanent (long term). d. The beam carries a single concentrated live load at mid-span of 70 KN. e. 20% of the live load is considered short term. f....

A reinforced concrete beam of normal weight concrete with an effective depth of 20 IN and...

A reinforced concrete beam of normal weight concrete with an effective depth of 20 IN and a width of 12 IN is reinforced with 3 IN2 of grade 60 (fy = 60 KSI) rebar. The beam has a concrete compressive strength f’c of 3000 PSI. (a) Determine the maximum ultimate moment which can be applied to the beam. (b) If the only dead load on the beam is self-weight, determine the allowable uniformly distributed live load which can be applied...

Please select the reinforcement spacing for the entire span of a simply supported beam on a...

Please select the reinforcement spacing for the entire span of a simply supported beam on a 22 ft span. Use the detailed method to calculate Vc. Do not use a shear envelope diagram use the regular shear force diagram. Use b = 16 in., d = 27 in., the main bending reinforcement consists of 4 #9 bars. The unfactored dead and live loads are 2.6 Kip/ft and 2.5 kip/ft, respectively, f’c = 4500 psi, and fy = 60,000 psi. Use...

Find the required amount of reinforcement required for the abdominium beam in order to support the...

Find the required amount of reinforcement required for the abdominium beam in order to support the cross-sectional bending moment MU= 525 kN·m under the counting load. Design cover thickness 40mm and stub reinforcement using D10. Compressed iron bars do not have to be surrendered, and the size of the cross-section can only be increased if the design is not possible under the given conditions. b = 320 mm, h = 550 mm, fck = 32 MPa, fy= 450 MPa, Using...

2. A simply supported rectangular concrete beam is to be made from M21 concrete grade and...

2. A simply supported rectangular concrete beam is to be made from M21 concrete grade and reinforced with steel bar of 345 MPa yield strength. It carries a uniformly distributed load of 12.5 kN/m and has a span of 6 m. Design the beam, assuming that the shape factor is 0.4. The weight density of steel is 77 kN/m3 and that of concrete is 24 kN/m3.

Determine the nominal concrete cover for a simply supported beam with exposure condition XC4. The concrete...

Determine the nominal concrete cover for a simply supported beam with exposure condition XC4. The concrete strength is 25MPa, the diameter of tension reinforcement is 32mm, diameter of shear link is 10mm, design working life is 50 years and the quality control is normal.

Question