Question

In: Civil Engineering

2.A simply supported beam has a width of 200mm and depth of 400mm is 4m long....

2.A simply supported beam has a width of 200mm and depth of 400mm is 4m long. It carries a
uniformly distributed load of 20 kN/m over the whole beam and a point load of 40 kN at the
center of the beam. Compute the maximum deflection if the maximum slope produced in the
beam is 2× ??-3 radian.

Solutions

Expert Solution

Ally Wells answered 10 months ago
Next > < Previous

Related Solutions

A simply supported beam has a width of 200mm and depth of 400mm is 4m long....
A simply supported beam has a width of 200mm and depth of 400mm is 4m long. It carries a uniformly distributed load of 20 kN/m over the whole beam and a point load of 40 kN at the center of the beam. Compute the maximum deflection if the maximum slope produced in the beam is 2× ??-3 radian.   
A beam 3m long is simply supported at its ends. The beam is loaded with a...
A beam 3m long is simply supported at its ends. The beam is loaded with a downward vertical load of 200N at a point 2m from the left support. USING AMM. a.) The maximum deflection is located at what distance from the left support? Answer: 1.63m b.) Calculate the maximum deflection assuming E = 50 GPa and I = 1x10^6 mm4 Answer 2.9mm
A beam 3m long is simply supported at its ends. The beam is loaded with a...
A beam 3m long is simply supported at its ends. The beam is loaded with a downward vertical load of 200N at a point 2m from the left support. Using DIM: a. The maximum deflection is located at what distance from the left support? b. Calculate the maximum deflection assuming E = 50 GPa and I = 1x10^6 mm4
Determine the required shear reinforcing for a simply supported concrete beam 7 meters long with a...
Determine the required shear reinforcing for a simply supported concrete beam 7 meters long with a cross section of 500 millimeters in depth and a width of 380 millimeters. Use fc = 35 MPa fy = 400 MPa. The longitudinal steel uses one row of 25M bars. The specific live load is 29 kKn/m. The beam is not exposed.
Consider a W30x99 beam (Fy = 60 ksi) that is simply supported, 30 ft. long, and...
Consider a W30x99 beam (Fy = 60 ksi) that is simply supported, 30 ft. long, and subjected to a point load at the midspan. The point service load consists of 60% live load and 40% dead load. Lateral supports exist at the ends only. Design code to comply with: 2016 AISC LRFD. (a) Determine the maximum point service load P for strong-axis bending assuming Cb = 1.0. (b) Redetermine the maximum point service load P for strong-axis bending considering proper...
You are analyzing a 40 FT long simply supported beam (b = 10 IN, d =...
You are analyzing a 40 FT long simply supported beam (b = 10 IN, d = 21.5 IN, h = 24 IN) in an existing building. The dead load on this beam is 1.2 KLF and you are tasked with deciding whether a load of 2 KLF of live load can be applied in addition. Based on the original plans, you think that the compressive strength of the concrete f’c = 3000 PSI and the yield strength of the rebar...
(1) A simply supported steel beam is 30' long and subjected to a uniform distributed 1.3...
(1) A simply supported steel beam is 30' long and subjected to a uniform distributed 1.3 kips per foot. What is the minimum required section modulus for this beam if we do not want its maximum stress to exceed 50 ksi? (2) What is the minimum inertia of the beam in the previous question if we do not want it to deflect more than 1/2" ?
What is the significance of the simply supported beam bridge and what is the implication simply...
What is the significance of the simply supported beam bridge and what is the implication simply supported beam is applied on the bridge?
Consider a concrete beam in an interior environment as follows: a. The beam is simply supported...
Consider a concrete beam in an interior environment as follows: a. The beam is simply supported with a design span of 4.8 metres. b. The dead load in the beam is uniformly distributed. c. Dead load on the beam, in addition to its own weight, is 6.9 KN/m of which 75% is permanent (long term). d. The beam carries a single concentrated live load at mid-span of 70 KN. e. 20% of the live load is considered short term. f....
A simply supported 7 ft long solid wooden beam is designed to carry a concentrated load...
A simply supported 7 ft long solid wooden beam is designed to carry a concentrated load P = 600 lbf in the center. The distance between supports is 72 inches. The cross sectional area is 2” (inches) wide and 6” (inches) high. Determine the moment of mass of the beam (lbm), inertia (in4) and deflection (in). This wood has the following material properties: Modulus of elasticity = 2.5 x 106 psi and Density = 40 lbm/ft3.
ADVERTISEMENT
Subjects
ADVERTISEMENT
Latest Questions
ADVERTISEMENT