Question

In: Civil Engineering

1) Due to the construction of a building, 150 kPa vertical stress increment takes place in...

1) Due to the construction of a building, 150 kPa vertical stress increment takes place in a clay layer. The thickness of clay layer is 8m and there are a very thin sand layer above and a thick sand layer below it. If the final settlement is 0.08m, calculate the followings:

a) Required time in terms of month for 0.04m consolidation settlement

b) Amount of settlement in terms of meter, after 4 months of construction

c) During the construction, a machine is intended to be placed in to the building. However, the machine is sensitive to the settlement and amount of the settlement should not exceed 0.02m after placing this machine. Calculate the required time to satisfy the prerequisite in terms of months.

d) k value of the clay layer

mv = 1*10-4, cv = 0.4 m/month

Solutions

Expert Solution


Related Solutions

Use Figure 1 and Table 1 for the following: Compute the vertical effective stress (σ'v) in...
Use Figure 1 and Table 1 for the following: Compute the vertical effective stress (σ'v) in kN/m2 at the center of the clay layer prior to the construction of the footing. Assuming a load of 1150 kN, use the Boussinesq procedure to determine increase in the vertical stress (Δσ) in kN/m2 at the center of the clay layer below the center of the footing. Assuming the values that you computed in (a) and (b) are representative for the entire thickness...
Red Man Construction is constructing a building. Construction began on January 1 and was completed on...
Red Man Construction is constructing a building. Construction began on January 1 and was completed on December 31. Expenditures were $6,400,000 on March 1, $5,280,000 on June 1, and $8,000,000 on December 31. Red Man borrowed $3,200,000 on January 1 on a 5-year, 12% note to help finance construction of the building. In addition, the company had outstanding all year a 10%, 3-year, $6,400,000 note payable and an 11%, 4-year, $12,000,000 note payable prepare all entries that are necessary
Red Man Construction is constructing a building. Construction began on January 1 and was completed on...
Red Man Construction is constructing a building. Construction began on January 1 and was completed on December 31. Expenditures were $6,400,000 on March 1, $5,280,000 on June 1, and $8,000,000 on December 31. Red Man borrowed $3,200,000 on January 1 on a 5-year, 12% note to help finance construction of the building. In addition, the company had outstanding all year a 10%, 3-year, $6,400,000 note payable and an 11%, 4-year, $12,000,000 note payable. what amount of interest should be charged...
Construction of a new building began on April 1 and was completed on October 29. Construction...
Construction of a new building began on April 1 and was completed on October 29. Construction expenditures were as follows: May 1 $3,300,000 July 30 2,200,000 September 1 1,740,000 October 1 2,640,000 MMI borrowed $5,000,000 at 6% on April 1 to help finance construction. This loan, plus interest, will be paid in 2022. The company also had a $6,650,000, 8% long-term note payable outstanding throughout 2021. Weighted Average Accumulated Expenditures were: [Round expenditure to nearest dollar] Date Expenditure Months financed...
Construction of a new building began on April 1 and was completed on October 29. Construction...
Construction of a new building began on April 1 and was completed on October 29. Construction expenditures were as follows: May 1 $3,300,000 July 30 2,200,000 September 1 1,740,000 October 1 2,640,000 MMI borrowed $5,000,000 at 6% on April 1 to help finance construction. This loan, plus interest, will be paid in 2022. The company also had a $6,650,000, 8% long-term note payable outstanding throughout 2021. Weighted Average Accumulated Expenditures were: [Round expenditure to nearest dollar] Date Expenditure Months financed...
Fire behavior and combustion have evolved throughout time due to changes in fuel loads, building construction,...
Fire behavior and combustion have evolved throughout time due to changes in fuel loads, building construction, and the application of science and research to firefighting strategy and tactics. What is the most prolific changes in fire behavior and combustion are being utilized in fire operations today and why the members of the fire service are resit's I've to adapt to these changes?
UVW began construction of a new office building on March 1, Y1. On the day construction...
UVW began construction of a new office building on March 1, Y1. On the day construction began, UVW borrowed $240,000 at 7% and immediately spent it on the project. An additional payment of $60,000 was also made on the day construction began. Additional expenditures of $75,000 were made on May 1 and August 31. Construction was complete and the building was placed in service on December 31, Y1. In addition to the $240,000 borrowed to finance the project, UVW also...
(2) Red Man Construction is constructing a building. Construction began on January 1 and was completed...
(2) Red Man Construction is constructing a building. Construction began on January 1 and was completed on December 31. Expenditures were $6,400,000 on March 1, $5,280,000 on June 1, and $8,000,000 on December 31. Red Man borrowed $3,200,000 on January 1 on a 5-year, 12% note to help finance construction of the building. In addition, the company had outstanding all year a 10%, 3-year, $6,400,000 note payable and an 11%, 4-year, $12,000,000 note payable. What amount of interest should be...
1 mol of an ideal gas at initial conditions p1=150 kPa, V1 =20 L was compressed...
1 mol of an ideal gas at initial conditions p1=150 kPa, V1 =20 L was compressed to p2 = 450 kPa through adiabatic reversible compression. Determine the work, heat, change of internal energy, enthalpy and entropy for the process. The gas heat capacity is Cp,m = 29.10 J K-1 mol-1.
1. Take a 150 mL Erlenmeyer flask from the Containers shelf and place it on the...
1. Take a 150 mL Erlenmeyer flask from the Containers shelf and place it on the workbench. 2. Add 10 mL of 6 M Hydrochloric acid (HCl) to the Erlenmeyer flask. Dilute with 10 mL of water. 3. Double-click on the Erlenmeyer flask to open the Item Properties window. Choose Close and click OK to plug the Erlenmeyer flask with an airtight stopper. 4. Take a thermometer and a pressure gauge from the Instruments shelf and attach each to the...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT