Question

In: Civil Engineering

A 35 ft simply supported beam is loaded with concentrated loads 15 ft in from each...

A 35 ft simply supported beam is loaded with concentrated loads 15 ft in from each support. On one end, the dead load is 8.0 kips and the live load is 18.0 kips. At the other end, the dead load is 4.0 kips and the live load is 9.0 kips. Include the self-weight of the beam in the design. Lateral supports are provided at the supports and the load points. Determine the least-weight W-shape to carry the load. Use A992 steel and Cb =1.0. Design by (a) LRFD and (b) ASD. [6.16-34]

Solutions

Expert Solution


Related Solutions

A simply supported 7 ft long solid wooden beam is designed to carry a concentrated load...
A simply supported 7 ft long solid wooden beam is designed to carry a concentrated load P = 600 lbf in the center. The distance between supports is 72 inches. The cross sectional area is 2” (inches) wide and 6” (inches) high. Determine the moment of mass of the beam (lbm), inertia (in4) and deflection (in). This wood has the following material properties: Modulus of elasticity = 2.5 x 106 psi and Density = 40 lbm/ft3.
A beam 3m long is simply supported at its ends. The beam is loaded with a...
A beam 3m long is simply supported at its ends. The beam is loaded with a downward vertical load of 200N at a point 2m from the left support. USING AMM. a.) The maximum deflection is located at what distance from the left support? Answer: 1.63m b.) Calculate the maximum deflection assuming E = 50 GPa and I = 1x10^6 mm4 Answer 2.9mm
A beam 3m long is simply supported at its ends. The beam is loaded with a...
A beam 3m long is simply supported at its ends. The beam is loaded with a downward vertical load of 200N at a point 2m from the left support. Using DIM: a. The maximum deflection is located at what distance from the left support? b. Calculate the maximum deflection assuming E = 50 GPa and I = 1x10^6 mm4
A simply supported beam with a span of 26 FT is used to carry a service...
A simply supported beam with a span of 26 FT is used to carry a service dead load (including self-weight) of 1.65 KLF and a service live load of 3.3 KLF and is reinforced with 4-#9 bars. The beam has a width b of 14 IN, an effective depth of 24.5 IN., and a height of 27 IN. The material strengths are f’c = 4000 PSI and fy = 60 KSI. The immediate deflection due to live load is limited...
A simply supported beam spans 35ft and carries a simply distrusted dead load of 0.2kip/ft including...
A simply supported beam spans 35ft and carries a simply distrusted dead load of 0.2kip/ft including the beam self-weight and live load of 0.8kip/ft. Determine the minimum required plastic section modulus and select the lightest-weight W-shape to carry the moment. Assume full lateral support and A992 steel. Design by (a) LRFD and (b) ASD
A simply supported beam is required to carry a moment of 50 kip-ft across a 25'...
A simply supported beam is required to carry a moment of 50 kip-ft across a 25' span. Assuming that 4 and 8 ksi concrete are available, with a cost difference of 30 percent. Use 60 ksi steel. Beam width is fixed at 12 inches. You can Vary h. a)design the beam using 2 different concretes - dont forget beta is different.
Consider a W30x99 beam (Fy = 60 ksi) that is simply supported, 30 ft. long, and...
Consider a W30x99 beam (Fy = 60 ksi) that is simply supported, 30 ft. long, and subjected to a point load at the midspan. The point service load consists of 60% live load and 40% dead load. Lateral supports exist at the ends only. Design code to comply with: 2016 AISC LRFD. (a) Determine the maximum point service load P for strong-axis bending assuming Cb = 1.0. (b) Redetermine the maximum point service load P for strong-axis bending considering proper...
You are analyzing a 40 FT long simply supported beam (b = 10 IN, d =...
You are analyzing a 40 FT long simply supported beam (b = 10 IN, d = 21.5 IN, h = 24 IN) in an existing building. The dead load on this beam is 1.2 KLF and you are tasked with deciding whether a load of 2 KLF of live load can be applied in addition. Based on the original plans, you think that the compressive strength of the concrete f’c = 3000 PSI and the yield strength of the rebar...
A simply supported beam of length 7m has a concentrated couple Mo (counter clockwise) of 10kNm...
A simply supported beam of length 7m has a concentrated couple Mo (counter clockwise) of 10kNm applied at one end. Using DIM(Double Integration Method): The maximum deflection is located at what distance from the applied load? Calculate the maximum deflection assuming E = 200 GPa and I = 60x10^6 mm4
A 15-m simply supported beam is subjected to a uniformly increasing load of zero, 3m from...
A 15-m simply supported beam is subjected to a uniformly increasing load of zero, 3m from the left support, to 30kN/m at the right support. A 20kN point load is also acting 1 meter from the left support. The cross section of the beam is 500mm x 800mm. Assume that tendons are applied in constant eccentricity of e = 150mm. Determine: Moment at midspan Maximum Moment Stress of the section where moment is maximum, assuming the effective Jacking Force to...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT