A suspension of calcium carbonate particles in water flows through a pipe. An engineer was asked...

A suspension of calcium carbonate particles in water flows through a pipe. An engineer was asked to determine both the flow rate and the composition of this slurry. The engineer proceeded to collect the stream in a graduated cylinder for a time given in the table below. The engineer weighed the cylinder, evaporate the collected water, and reweighed the cylinder. The following results are obtained based on two occasion

Item	Sample 1	Sample 2
Time to collect	1 min	1 min
Mass of cylinder	65.0 g	65.5 g
Mass of cylinder and collected slurry	565 g	595.5 g
Volume collected	455 mL	450 mL
Mass of cylinder after evaporation	215 g	251 g

create Matlab programming to calculate:

The volumetric flow rate and mass flow rate of the suspension
The density of the suspension
The mass fraction of CaCO3 in the suspension

Expert Solution

Amanda K answered 1 year ago

Water flows through a cast iron pipe with a diameter of 30 mm. The pipe is...

Water flows through a cast iron pipe with a diameter of 30 mm. The pipe is inclined at an angle of 3 degrees from horizontal and is 40 m long. The water flows due to gravity only. What is the maximum volume flow rate of the water? You may ignore any minor loses.

Water flows through the pipe in the figure below and exits to the atmosphere at the...

Water flows through the pipe in the figure below and exits to the atmosphere at the right end of section C. The diameter of the pipe is 2.12 cm at A, 4.24 cm at B, and 0.880 cm at C. The gauge pressure in the pipe at the center of section A is 1.25 atm and the flow rate is 0.856 L/s. The vertical pipes are open to the air. Find the level (above the flow midline as shown) of...

What is the molar soulbility of calcium carbonate in pure water? the ksp value for calcium...

What is the molar soulbility of calcium carbonate in pure water? the ksp value for calcium carbonate is 4.50x10-9. What is the molar solubility in 0.1 M CaCl.

Water flows upward and then is discharged to the right through a 3 inch diameter pipe...

Water flows upward and then is discharged to the right through a 3 inch diameter pipe elbow, at a steady flow rate of 1 cubic foot per second, the gage pressure at the entrance to the elbow is 30 psi. What vertical and horizontal force is necessary to hold the elbow stationary, neglecting any required torque.

Water flows through a circular pipe with a constant radius of 5.0 cm. The speed and...

Water flows through a circular pipe with a constant radius of 5.0 cm. The speed and pressure at point A is 2.0 m/s and 2.0 x10^5 Pa respectively. What is the pressure at point B, which is 1.0 m higher than at point A.

a) Water (Densitywater = 1,000 kg/m3) flows through a pipe that narrows. At point A it...

a) Water (Densitywater = 1,000 kg/m3) flows through a pipe that narrows. At point A it is determined that the water flows with a velocity of VA = 93 m/s. At point B it is determined that the water flows with a velocity of VB = 193 m/s.What is the nagnitude of the difference in pressure between points A and B. b) Two trains pass each other. Train A is traveling 36 m/s east. Train B is traveling 23 m/s...

A 8.0-cm-diameter horizontal pipe gradually narrows to 5.0 cm . When water flows through this pipe...

A 8.0-cm-diameter horizontal pipe gradually narrows to 5.0 cm . When water flows through this pipe at a certain rate, the gauge pressure in these two sections is 31.0 kPa and 25.0 kPa , respectively. What is the volume rate of flow?

what is the handbook value of concentration of calcium carbonate in hot water

what is the handbook value of the concentration of calcium carbonate in hot water?

Question 1) Water at 20 C flows through a galvanized pipe at an average speed of...

Question 1) Water at 20 C flows through a galvanized pipe at an average speed of 2.5 m / s. The diameter of the pipe is 150 mm. The roughness of the pipe surface is 60 μm. Calculate the pressure drop in this pipe since the total length of the pipe is 300 meters. Take the necessary values for calculations from tables and diagrams.

Question