Water flows through a cast iron pipe with a diameter of 30 mm. The pipe is...

Water flows through a cast iron pipe with a diameter of 30 mm. The pipe is inclined at an angle of 3 degrees from horizontal and is 40 m long. The water flows due to gravity only. What is the maximum volume flow rate of the water?

You may ignore any minor loses.

Expert Solution

length L = 40 m

diameter D = 30 mm = 0.03 m

acceleration due to gravity g = 9.81 m/s2

head = h

head loss = hL

Maximum volume flow rate of water (Discharge)= Q

Maximum volume flow rate considering major loss(frictional loss ) = 0.000812 m3/s

Maximum volume flow rate neglecting all loses both major and minor losses = 0.00452 m3/s

Ally Wells answered 1 year ago

A cast iron water pipe of 500 mm inside diameter and 20 mm thick, is supported...

A cast iron water pipe of 500 mm inside diameter and 20 mm thick, is supported over a span of 10 meters. Find the maximum bending stress in the pipe metal, when the pipe is running full. Take density of cast iron = 70.6 kN/m3 and water = 9.8 kN/m3

The flowrate for water traveling through a horizontal 300 m-long cast iron pipe with a diameter...

The flowrate for water traveling through a horizontal 300 m-long cast iron pipe with a diameter of 0.6 m and a pressure drop of 17.2 kPa is to be found. P.S. use iterative approach to find values of f and then V using that f.

1)10 m3 /h of water flows through a pipe with 100 mm inside diameter. Calculate the...

1)10 m3 /h of water flows through a pipe with 100 mm inside diameter. Calculate the flow velocity inside this pipe. ? 2) A river discharges 100 m3 of water to the sea every 2 seconds. What is the flow-rate of this river expressed in m3/s?

Water is flowing through a pipe having the diameter 200 mm and 100 mm at sections...

Water is flowing through a pipe having the diameter 200 mm and 100 mm at sections 1 and 2 respectively. The rate of flow through the pipe is 35 liters per second. The section 1 is 6000 mm and section 2 is 4000 mm above the datum line. If the pressure at the section 1 is 0.4 N/mm2, find the intensity of pressure at section 2.

What diameter of cast iron pipe would be required to ensure that a discharge of 0.2...

What diameter of cast iron pipe would be required to ensure that a discharge of 0.2 m3/s would not cause a head loss in excess of 0.01 m/100 m of pipe length, assume water temperature is 20 oC

) A 50 mm-diameter propeller was installed in a 150 mm-diameter water pipe and the propeller...

) A 50 mm-diameter propeller was installed in a 150 mm-diameter water pipe and the propeller speed was measured for a range of water discharge in the pipe. The water had a density and dynamic viscosity of 1000 kg/m3 and 0.00112 Ns/m2 respectively. The measured results were as follows: Q (litres/s): 12 28 45 63 95 120 160 180 N (rps): 5 10 15 20 30 40 60 80 Plot the dependence of propeller coefficient against propeller Reynolds number. A...

Water flows upward and then is discharged to the right through a 3 inch diameter pipe...

Water flows upward and then is discharged to the right through a 3 inch diameter pipe elbow, at a steady flow rate of 1 cubic foot per second, the gage pressure at the entrance to the elbow is 30 psi. What vertical and horizontal force is necessary to hold the elbow stationary, neglecting any required torque.

Plot the head loss in a 500 m long 200 mm cast iron pipe for the...

Plot the head loss in a 500 m long 200 mm cast iron pipe for the following flow rates; 0.001, 0.01, 0.1, and 1 m3/s. Use (a) the Moody Diagram and (b) the Swamee-Jain equation to find the friction factor and (c) the Hazen-Williams Eq. Discuss why the losses are similar or different for parts a and c

(c) A 50 mm-diameter propeller was installed in a 150 mm-diameter water pipe and the propeller...

(c) A 50 mm-diameter propeller was installed in a 150 mm-diameter water pipe and the propeller speed was measured for a range of water discharge in the pipe. The water had a density and dynamic viscosity of 1000 kg/m3 and 0.00112 Ns/m2 respectively. The measured results were as follows: Q (litres/s): 12 28 45 63 95 120 160 180 N (rps): 5 10 15 20 30 40 60 80 Plot the dependence of propeller coefficient against propeller Reynolds number. A...

A 8.0-cm-diameter horizontal pipe gradually narrows to 5.0 cm . When water flows through this pipe...

A 8.0-cm-diameter horizontal pipe gradually narrows to 5.0 cm . When water flows through this pipe at a certain rate, the gauge pressure in these two sections is 31.0 kPa and 25.0 kPa , respectively. What is the volume rate of flow?

Question