Question

In: Electrical Engineering

Starting from the dynamic equations of the PM DC motor obtain the voltage-to-speed transfer function in...

Starting from the dynamic equations of the PM DC motor obtain the voltage-to-speed
transfer function in s-domain. Draw the block diagram.

Solutions

Expert Solution

Manojponduru answered 11 months ago
Next > < Previous

Related Solutions

Starting from the dynamic equations of the PM DC motor obtain the voltage-to-speed transfer function in...
Starting from the dynamic equations of the PM DC motor obtain the voltage-to-speed transfer function in s-domain. Draw the block diagram.
Problem: A PM DC motor has the following parameters: Rated Power 10 hp; Rated armature voltage...
Problem: A PM DC motor has the following parameters: Rated Power 10 hp; Rated armature voltage 230 V-DC; Rated RPM: 1800; Armature Resistance: 0.2 Ohm Armature Inductance: 0.005 H Inertia (motor plus mechanical load): 0.1 kgm^2; Viscous friction coefficient: 0.015 Nms 1. Compute the voltage constant of the motor. Also compute the rated current and rated torque of the motor (obtained at the rated RPM). If the motor is supplied by 230 V across the armature, and the only torque...
(a) In DC motor, quadrant of operation can be defined by the armature voltage and current...
(a) In DC motor, quadrant of operation can be defined by the armature voltage and current of the motor. By using an appropriate diagram, briefly explain the definition of all four quadrant of operation based on armature voltage and current. (b) A chopper is used to control speed of 45.36 kW, 1750 rpm, 240 V, 189 A permanent magnet DC motor with 0.01 Ω armature resistance. This chopper-fed DC motor is able to operate in both motoring and braking mode...
I have a question for the effect and difference on a DC motor for the speed(...
I have a question for the effect and difference on a DC motor for the speed( rad/s) in time (sec) if you apply: 1. Nothing (so no charge in the circuit only the mecanic charge of the generator) 2. A resistant charge (only the resistant is plug in with the generator) 3. Short circuit (No exterior electric charge but the terminals are bounds together so an excessive amount of current flow into the circuit) 4. Capacitive charge (only the capacitor...
In order for a dc motor to function properly, it must be protected from physical damage...
In order for a dc motor to function properly, it must be protected from physical damage during the starting period. At starting conditions, the motor is not rotating, and armature generated voltage EA = 0 V. Since the internal resistance of a normal DC motor is very low, a very high current flows. It is possible for a motor to be severely damaged by such currents, even if they last for only a moment. A solution to the problem of...
Design and analyse of a circuit which turns a DC motor at a speed which is...
Design and analyse of a circuit which turns a DC motor at a speed which is proportional to how much a temperature is away from a set temperature, and turns: Clockwise when temperature is greater than (say) 25 degrees C. Anticlockwise when the temperature is less than (say) 20 degrees C. Such a circuit might be used to regulate the temperature of a room by turning a ceiling fan to move warm air in/out of that room (using the roof...
A) Refer to the diagram on “Speed Control of a Shunt Wound DC Motor. Suppose the...
A) Refer to the diagram on “Speed Control of a Shunt Wound DC Motor. Suppose the no load voltage V = 90V, Ra + R1 = 4 ohms, Rsh + RF = 130 ohms, and the motor runs at a rated speed of 1000 RPM when IL = 4 amps. What is the back EMF VB in volts when the motor runs at IL = 6 amps? Note: Type a 1-decimal number, rounded off to the nearest 0.1 B) How...
When running at 4000rpm with an applied voltage of 42v, a DC permanent magnet motor develops...
When running at 4000rpm with an applied voltage of 42v, a DC permanent magnet motor develops 23.1W of output power. The motor has a theoretical no-load speed of 6000rpm at an applied voltage of 42v. What is the motor output torque at 4000rpm in N-m, What is the motors theoretical back-EMF constant, What is the motors theoretical torque constant, What is the motors theoretical stall torque, What is the motors armature resistance, What is the motors efficiency at 4000rpm when...
Why is the starting current high in a DC motor? Explain the working of a four-point...
Why is the starting current high in a DC motor? Explain the working of a four-point starter for a DC machine.
DO NOT COPY FROM PREVIOUS SOLUTIONS Design a low-voltage, high-current, shunt-excited DC motor for an industrial...
DO NOT COPY FROM PREVIOUS SOLUTIONS Design a low-voltage, high-current, shunt-excited DC motor for an industrial facility. The motor should have the following specifications: The output power of the machine is expected to be between (50) hp. The copper losses in the machine should be between 4% and 7% of the output power. The brush losses in the machine should be between 2% and 5% of the copper losses. The no load power should not exceed 6% of the output...
ADVERTISEMENT
Subjects
ADVERTISEMENT
Latest Questions
ADVERTISEMENT