Question
In: Civil Engineering
A 12-inch diameter cast iron pipe conveys 1500 gpm of liquid at an industrial facility. At...
A 12-inch diameter cast iron pipe conveys 1500 gpm of liquid at an industrial facility. At one point in the pipe, call it point A, a gage indicates that the pressure is 45 psi. Another point in the pipe, call it point B, is 175 ft downstream of point A (measured along the pipe). (a) Determine the head loss (ft) between points A and B if the liquid is: (i) SAE 30 oil at 60°F; (ii) water at 60°F. (b) Determine the pressure at point B, for both liquids, in the following cases: (i) point A is 18 ft higher than point B, (ii) point A is at the same elevation as point B, (iii) point A is 18 ft lower than point B.
Solutions
Ally Wells answered 5 months agoRelated Solutions
A 12-inch diameter cast iron pipe conveys 1500 gpm of liquid at an industrial facility. At...
A 12-inch diameter cast iron pipe conveys 1500 gpm of liquid at
an industrial facility. At one point in the pipe, call it point A,
a gage indicates that the pressure is 45 psi. Another point in the
pipe, call it point B, is 175 ft downstream of point A (measured
along the pipe).
(a) Determine the head loss (ft) between points A and B if the
liquid is: (i) SAE 30 oil at 60°F; (ii) water at 60°F.
(b)...
A 12-inch diameter cast iron pipe conveys 1500 gpm of liquid at an industrial facility. At...
A 12-inch diameter cast iron pipe conveys 1500 gpm of liquid at
an industrial facility. At one point in the pipe, call it point A,
a gage indicates that the pressure is 45 psi. Another point in the
pipe, call it point B, is 175 ft downstream of point A (measured
along the pipe). (a) Determine the head loss (ft) between points A
and B if the liquid is: (i) SAE 30 oil at 60°F; (ii) water at 60°F.
(b)...
A 12-inch diameter cast iron pipe conveys 1500 gpm of liquid at an industrial facility. At...
A 12-inch diameter cast iron pipe conveys 1500 gpm of liquid at
an industrial facility. At one point in the pipe, call it point A,
a gage indicates that the pressure is 45 psi. Another point in the
pipe, call it point B, is 175 ft downstream of point A (measured
along the pipe). (a) Determine the head loss (ft) between points A
and B if the liquid is: (i) SAE 30 oil at 60°F; (ii) water at
60°F. (b) Determine...
Water flows through a cast iron pipe with a diameter of 30 mm. The pipe is...
Water flows through a cast iron pipe with a diameter of 30 mm.
The pipe is inclined at an angle of 3 degrees from horizontal and
is 40 m long. The water flows due to gravity only. What is the
maximum volume flow rate of the water?
You may ignore any minor loses.
What diameter of cast iron pipe would be required to ensure that a discharge of 0.2...
What diameter of cast iron pipe would be required to ensure that
a discharge of 0.2 m3/s would not cause a head loss in excess of
0.01 m/100 m of pipe length, assume water temperature is 20 oC
The flowrate for water traveling through a horizontal 300 m-long cast iron pipe with a diameter...
The flowrate for water traveling through a horizontal 300 m-long
cast iron pipe with a diameter of 0.6 m and a pressure drop of 17.2
kPa is to be found. P.S. use iterative approach to find values of f
and then V using that f.
A cast iron water pipe of 500 mm inside diameter and 20 mm thick, is supported...
A cast iron water pipe of 500 mm inside diameter and 20 mm
thick, is supported over a span of 10 meters. Find the maximum
bending stress in the pipe metal, when the pipe is running full.
Take density of cast iron = 70.6 kN/m3 and water = 9.8 kN/m3
An existing 36-inch diameter concrete gravity sewer installed on a slope of 0.25% currently conveys a...
An existing 36-inch diameter concrete gravity sewer installed on
a slope of 0.25% currently conveys a peak flow rate of 12 cfs. A
builder proposes to connect a new residential development to this
existing sewer. Projected peak flow from this new development is 4
cfs.
a) Depth of flow in sewer before new development is
connected
b) Depth of flow in sewer after new development is connected
c) Flow velocity in sewer after new development is connected
d) Flow type...
An existing 36-inch diameter concrete gravity sewer installed on a slope of 0.25% currently conveys a...
An existing 36-inch diameter concrete gravity sewer installed on
a slope of 0.25% currently conveys a peak flow rate of 12 cfs. A
builder proposes to connect a new residential development to this
existing sewer. Projected peak flow from this new development is 4
cfs.
a) Depth of flow in sewer before new development is
connected
b) Depth of flow in sewer after new development is connected
c) Flow velocity in sewer after new development is connected
d) Flow type...
Water flows upward and then is discharged to the right through a 3 inch diameter pipe...
Water flows upward and then is discharged to the right through a
3 inch diameter pipe elbow, at a steady flow rate of 1 cubic foot
per second, the gage pressure at the entrance to the elbow is 30
psi. What vertical and horizontal force is necessary to hold the
elbow stationary, neglecting any required torque.
ADVERTISEMENT
ADVERTISEMENT
Latest Questions
- * Discuss TWO economic benefits, and TWO economic harms, to the U.S. economy, of a high...
- F. Pierce Products Inc. is considering changing its capital structure. F. Pierce currently has no debt...
- Costs of retailer selling a quintal of mango Sorting and grading 200 Transportation 300 Loading and...
- Recall that in chapter 25 we learned about the aggregate production function, in which the factors...
- Discuss fully Stalin’s efforts to stimulate Soviet industrial and agricultural production through his five year plans...
- *******Information to know prior to the questions: The product being offered in fresh produce sold in...
- Which brain scan methodologies are important for cognitive scientists? Why? - Please make the answer above...
ADVERTISEMENT