Question
In: Civil Engineering
A 12-inch diameter cast iron pipe conveys 1500 gpm of liquid at an industrial facility. At...
A 12-inch diameter cast iron pipe conveys 1500 gpm of liquid at an industrial facility. At one point in the pipe, call it point A, a gage indicates that the pressure is 45 psi. Another point in the pipe, call it point B, is 175 ft downstream of point A (measured along the pipe). (a) Determine the head loss (ft) between points A and B if the liquid is: (i) SAE 30 oil at 60°F; (ii) water at 60°F. (b) Determine the pressure at point B, for both liquids, in the following cases: (i) point A is 18 ft higher than point B, (ii) point A is at the same elevation as point B, (iii) point A is 18 ft lower than point B.
Solutions
Ally Wells answered 1 year agoRelated Solutions
A 12-inch diameter cast iron pipe conveys 1500 gpm of liquid at an industrial facility. At...
A 12-inch diameter cast iron pipe conveys 1500 gpm of liquid at
an industrial facility. At one point in the pipe, call it point A,
a gage indicates that the pressure is 45 psi. Another point in the
pipe, call it point B, is 175 ft downstream of point A (measured
along the pipe).
(a) Determine the head loss (ft) between points A and B if the
liquid is: (i) SAE 30 oil at 60°F; (ii) water at 60°F.
(b)...
A 12-inch diameter cast iron pipe conveys 1500 gpm of liquid at an industrial facility. At...
A 12-inch diameter cast iron pipe conveys 1500 gpm of liquid at
an industrial facility. At one point in the pipe, call it point A,
a gage indicates that the pressure is 45 psi. Another point in the
pipe, call it point B, is 175 ft downstream of point A (measured
along the pipe). (a) Determine the head loss (ft) between points A
and B if the liquid is: (i) SAE 30 oil at 60°F; (ii) water at 60°F.
(b)...
A 12-inch diameter cast iron pipe conveys 1500 gpm of liquid at an industrial facility. At...
A 12-inch diameter cast iron pipe conveys 1500 gpm of liquid at
an industrial facility. At one point in the pipe, call it point A,
a gage indicates that the pressure is 45 psi. Another point in the
pipe, call it point B, is 175 ft downstream of point A (measured
along the pipe). (a) Determine the head loss (ft) between points A
and B if the liquid is: (i) SAE 30 oil at 60°F; (ii) water at
60°F. (b) Determine...
Water flows through a cast iron pipe with a diameter of 30 mm. The pipe is...
Water flows through a cast iron pipe with a diameter of 30 mm.
The pipe is inclined at an angle of 3 degrees from horizontal and
is 40 m long. The water flows due to gravity only. What is the
maximum volume flow rate of the water?
You may ignore any minor loses.
What diameter of cast iron pipe would be required to ensure that a discharge of 0.2...
What diameter of cast iron pipe would be required to ensure that
a discharge of 0.2 m3/s would not cause a head loss in excess of
0.01 m/100 m of pipe length, assume water temperature is 20 oC
The flowrate for water traveling through a horizontal 300 m-long cast iron pipe with a diameter...
The flowrate for water traveling through a horizontal 300 m-long
cast iron pipe with a diameter of 0.6 m and a pressure drop of 17.2
kPa is to be found. P.S. use iterative approach to find values of f
and then V using that f.
A cast iron water pipe of 500 mm inside diameter and 20 mm thick, is supported...
A cast iron water pipe of 500 mm inside diameter and 20 mm
thick, is supported over a span of 10 meters. Find the maximum
bending stress in the pipe metal, when the pipe is running full.
Take density of cast iron = 70.6 kN/m3 and water = 9.8 kN/m3
An existing 36-inch diameter concrete gravity sewer installed on a slope of 0.25% currently conveys a...
An existing 36-inch diameter concrete gravity sewer installed on
a slope of 0.25% currently conveys a peak flow rate of 12 cfs. A
builder proposes to connect a new residential development to this
existing sewer. Projected peak flow from this new development is 4
cfs.
a) Depth of flow in sewer before new development is
connected
b) Depth of flow in sewer after new development is connected
c) Flow velocity in sewer after new development is connected
d) Flow type...
An existing 36-inch diameter concrete gravity sewer installed on a slope of 0.25% currently conveys a...
An existing 36-inch diameter concrete gravity sewer installed on
a slope of 0.25% currently conveys a peak flow rate of 12 cfs. A
builder proposes to connect a new residential development to this
existing sewer. Projected peak flow from this new development is 4
cfs.
a) Depth of flow in sewer before new development is
connected
b) Depth of flow in sewer after new development is connected
c) Flow velocity in sewer after new development is connected
d) Flow type...
A 32 inch diameter pump handling 22000 GPM flow of water coming from an atmospheric tank...
A 32 inch diameter pump handling 22000 GPM flow of water coming
from an atmospheric tank storage is running at 1170 rpm. The water
temperature can be taken at 25 C. The suction line is 20 meter long
at 6 inch diameter. The pump suction is 0.4 meter above ground
level. The tank storage is elevated on a 1 meter high platform.
Assume friction factor of 0.02. Specific Gravity of water at 25 C
is 0.9967. NPSH required is 34...
ADVERTISEMENT
ADVERTISEMENT
Latest Questions
- -what is the pH of HCl 0,1M and NaCl 0,1M mixed together solution? -What is the...
- function X=extractDWT(x_train,startS,endS,wStep,wRange) % x_train = input signal % startS = from second % endS = end...
- Do you agree that Social Loafing is similar to Theory X. Give an example to support...
- Computing Cost of Goods Sold and Ending Inventory. Bartov Corporation reports the following beginning inventory and...
- SQL FORMAT (11-13 are completed and correct) -- 11. what are the names of all students...
- You have been hired as a capital budgeting analyst by Advent Sports, a sporting goods firm...
- DESCRIBE WHAT HAPPENS WHEN WE BECOME CONSCIOUS OF SOMETHING. WHAT HAS TO HAPPEN FOR CONSCIOUS AWARENESS...
ADVERTISEMENT