Design a state Variable Filter that has a corner frequency of 100 KHz and a quality...

Design a state Variable Filter that has a corner frequency of 100 KHz and a quality factor (Q) of 20. Assume both the frequency-determining resistors and capacitors are equal.

Solutions

Expert Solution

Manojponduru answered 9 months ago

Next > < Previous

Related Solutions

Design an active low pass filter with a corner frequency of 50 Hz and amplification of 10

Design an active low pass filter with a corner frequency of 50 Hz and amplification of 10. Pick the values of the resistor and capacitor based on your own judgement to keep the cost reasonably low (simpler circuit design with less components is better).

Design a bandstop filter with a cutoff frequency of -3dB at W1 = 100 rad/s and...

Design a bandstop filter with a cutoff frequency of -3dB at W1 = 100 rad/s and W2 = 10,000rad/s. Confirm by plotting the magnitude and phase of the transfer function in matlab.

Design an analog elliptic lowpass IIR filter with specifications Fp=10 kHz., Ap=1 dB, Fs=15 kHz. And...

Design an analog elliptic lowpass IIR filter with specifications Fp=10 kHz., Ap=1 dB, Fs=15 kHz. And As=50 dB. Provide the following plots in MATLAB: a. Magnitude b. Log-magnitude c. Group-delay d. Impulse response e. Pole-zero

Specify the aliasing frequency of a signal that has a maximum frequency of 75 kHz and...

Specify the aliasing frequency of a signal that has a maximum frequency of 75 kHz and a sample frequency of 100 kHz. Use the folding diagram.

A boost converter has an input voltage Vin= 10 V, switching frequency fs= 100 kHz, duty...

A boost converter has an input voltage Vin= 10 V, switching frequency fs= 100 kHz, duty ratio d=50%, load resistance RL= 20Ω, inductance 100μH, and capacitance 680 μF. If you were trying to make a boost converter enter DCM, but your load resistor could not reach Rcrit, what other controllable parameters (not including Vin) could you change to reduce the lowest value of i_L to zero? Explain your reasoning.

A capacitor is connected to an ac generator that has a frequency of 3.2 kHz and...

A capacitor is connected to an ac generator that has a frequency of 3.2 kHz and produces a rms voltage of 1.3 V. The rms current in the capacitor is 29 mA. When the same capacitor is connected to a second ac generator that has a frequency of 5.1 kHz, the rms current in the capacitor is 86mA. What rms voltage does the second generator produce?

A buck-boost converter has an input voltage V_in= 10 V, switching frequency fs= 100 kHz, duty...

A buck-boost converter has an input voltage V_in= 10 V, switching frequency fs= 100 kHz, duty ratio d= 30%, load resistance R_L= 20Ω, inductance =100 μH, and capacitance= 680 μF. 1) Calculate the following values, and include units in your answers: a) Peak-to-peak current ripple through the inductor, Δ_iL b) Average inductor current that will cause the converter to enter DCM b) Load resistance that will cause the converter to enter DCM (R_crit) d) Average voltage across the inductor insteady-state

Butterworth filter a)Design a 5th order low pass Butterworth low-pass filter with a cut-off frequency of...

Butterworth filter a)Design a 5th order low pass Butterworth low-pass filter with a cut-off frequency of 1592 Hz and a dc gain of 3dB. Find and present the mathematical transfer function of the filter, showing all your steps. b) Write a Matlab code to plot the magnitude of this function with a linear scale in dB units on the ordinate, and a log scale of frequency on the abscissa. The plot range should be: ordinate- linear scale from -100dB to...

a. Design a broadband Butterworth bandpass filter with a lower cutoff frequency of 500 Hz and...

a. Design a broadband Butterworth bandpass filter with a lower cutoff frequency of 500 Hz and an upper cutoff frequency of 4500 Hz. The passband gain of the filter is 20 dB. The gain should be down at least 15 dB at 200 Hz and 11.25 kHz. Use 20 nF capacitors in the high-pass circuit and 10 k\Omega resistors in the low-pass circuit. b) Draw a circuit diagram of the filter and label all the components.

Design an active high pass filter with a high frequency gain of 5 and a cutoff...

Design an active high pass filter with a high frequency gain of 5 and a cutoff frequency of 2kHz. Use a 0.1 uF capacitor in your design.

Subjects