Question

In: Electrical Engineering

Design and simulate a first order high pass filter so that it has a cutoff frequency...

Design and simulate a first order high pass filter so that it has a cutoff frequency of 2 kHz and a passband gain of 1.

please use online multisim

Solutions

Expert Solution

Manojponduru answered 4 months ago
Next > < Previous

Related Solutions

Design and simulate a first order low pass filter so that it has a cutoff frequency...
Design and simulate a first order low pass filter so that it has a cutoff frequency of 2 kHz and a passband gain of 1. please use online multisim
Design a first order, high pass active filter with a cutoff frequency of 20 krad/sec. Cascade...
Design a first order, high pass active filter with a cutoff frequency of 20 krad/sec. Cascade Four of this filter designed and find reasonable values for the resistor and capacitor. Obtain the transfer function and show a circuit schematic for your filter. Plot the Bode plot
Design an active high pass filter with a high frequency gain of 5 and a cutoff...
Design an active high pass filter with a high frequency gain of 5 and a cutoff frequency of 2kHz. Use a 0.1 uF capacitor in your design.
Butterworth filter a)Design a 5th order low pass Butterworth low-pass filter with a cut-off frequency of...
Butterworth filter a)Design a 5th order low pass Butterworth low-pass filter with a cut-off frequency of 1592 Hz and a dc gain of 3dB. Find and present the mathematical transfer function of the filter, showing all your steps. b) Write a Matlab code to plot the magnitude of this function with a linear scale in dB units on the ordinate, and a log scale of frequency on the abscissa. The plot range should be: ordinate- linear scale from -100dB to...
Design a second order (two pole) high-pass filter for the following specifications Cut-off frequency, fo or...
Design a second order (two pole) high-pass filter for the following specifications Cut-off frequency, fo or fH = 2kHz   Maximally Flat, i.e. Q=1/√2 > Justify any assumption you make. > Draw circuit with all designed values. > Draw the frequency response (Gain magnitude only)
Design and build an active second order low pass filter with cut off frequency of 8kHz...
Design and build an active second order low pass filter with cut off frequency of 8kHz using opamp -Show circuit diagram -Show input voltage and frequency - Show all calculations and placement of indicator to measure output frequency to measure cut off
Design and build an active second order low pass filter with cut off frequency of 8kHz...
Design and build an active second order low pass filter with cut off frequency of 8kHz -Show circuit diagram -Show input voltage and frequency - Show all calculations and placement of indicator to measure output frequency to measure cut off
a. Design a broadband Butterworth bandpass filter with a lower cutoff frequency of 500 Hz and...
a. Design a broadband Butterworth bandpass filter with a lower cutoff frequency of 500 Hz and an upper cutoff frequency of 4500 Hz. The passband gain of the filter is 20 dB. The gain should be down at least 15 dB at 200 Hz and 11.25 kHz. Use 20 nF capacitors in the high-pass circuit and 10 k\Omega resistors in the low-pass circuit. b) Draw a circuit diagram of the filter and label all the components.
Design a bandstop filter with a cutoff frequency of -3dB at W1 = 100 rad/s and...
Design a bandstop filter with a cutoff frequency of -3dB at W1 = 100 rad/s and W2 = 10,000rad/s. Confirm by plotting the magnitude and phase of the transfer function in matlab.
Using a general Op-Amp 741, design a first order and a second-order low-pass filter with cut...
Using a general Op-Amp 741, design a first order and a second-order low-pass filter with cut off frequent of 5kHz. Subject sinusoidal inputs with frequency from 1kHz to 10kHz and plot the frequency responses for both the filters and provide your opinion.
ADVERTISEMENT
Subjects
ADVERTISEMENT
Latest Questions
ADVERTISEMENT