a) Draw the Integral Receiver circuit with input resistance (R1) 5 KΩ, feedback capacitor (CF) 10...

a) Draw the Integral Receiver circuit with input resistance (R1) 5 KΩ, feedback capacitor (CF) 10 nF and feedback resistance (RF) 100 KΩ.
b) In the case of applying a signal in the square wave form with ± 1 V and a frequency of 1 kHz as the input voltage, show whether the circuit will function or not.
c) Draw the output voltage (Vo) waveform with the input voltage on a scale.

Expert Solution

Manojponduru answered 1 year ago

The RF amplifier of a receiver has an input resistance of 1 kΩ, and equivalent shot...

The RF amplifier of a receiver has an input resistance of 1 kΩ, and equivalent shot noise resistance of 2 kΩ, a gain of 25, and a load resistance of 125 kΩ. Given that the bandwidth is 1.0 MHz and the temperature is 20 °C. If this receiver is connected to an antenna with an impedance of 75 Ω, calculate the noise figure. (in dB)

Draw a circuit with a battery of 90 V is connected to four resistors, R1 =10...

Draw a circuit with a battery of 90 V is connected to four resistors, R1 =10 Ω, R2,= 20 Ω , R3 =30 Ω and R4= 40 Ω, as follows. Resistors R1 and R2 are connected in parallel with each other, resistors R3 and R4 are connected in parallel with each other, and both parallel sets of resistors are connected in series with each other across the battery. (20 Points) a. Find the equivalent resistor R12, for the partial circuits...

5. a)Which component offers a measureable resistance to the circuit: Resistor or Capacitor? b) Let's say...

5. a)Which component offers a measureable resistance to the circuit: Resistor or Capacitor? b) Let's say you measure t1/2 to be 0.3018 seconds and the resistance in the circuit is 68 Ohms. Then what is the capacitance in micro Farads? answer in micro Farads. c) t1/2 means that the voltage (or charge) of the system will increase to half more of what is left in a time equal to t1/2 seconds. Therefore if a system is already at half charge...

Draw and analyze a four resister BJT (CE) bias circuit with the following values: R1=10...

Draw and analyze a four resister BJT (CE) bias circuit with the following values: R1=10 kΩ, R2=12 kΩ, RC=5 kΩ, RE=3 kΩ and VCC=12 V, Find the operating points ICQ and VCEQ Assume a BJT transistor (npn) with β=100 and VBE=0.7V

1. For a resistor capacitor circuit, what is the relationship between impedance and capacitive resistance? ☐...

1. For a resistor capacitor circuit, what is the relationship between impedance and capacitive resistance? ☐ Z = R2-XC2 ☐ Z = R2+XC2 ☐ Z = R-XC ☐ Z = R+XC 2. For an inductor circuit, what happens to the energy? ☐ Lost in the inductor ☐ Supplied by the inductor ☐ Zero net energy in the inductor ☐ None of these 3. What is the phase for a resistor inductor circuit? ☐ -90° ☐ +90° ☐ +45° ☐...

Design a circuit where the voltage across the capacitor matches the input step function as closely...

Design a circuit where the voltage across the capacitor matches the input step function as closely as possible. Sketch/show a picture of your result and which circuit parameters (R and C you used). Explain why the output looks like it does. Design a circuit where the voltage across the capacitor looks like a triangle wave (each peak looks like a triangle). Sketch/show a picture of your result and which circuit parameters (R and C you used). Explain why the output...

An LC circuit is built with a 10 mH inductor and an 12.0 pF capacitor. The...

An LC circuit is built with a 10 mH inductor and an 12.0 pF capacitor. The capacitor voltage has its maximum value of 40 V at t=0s. Part A How long is it until the capacitor is first fully discharged? Express your answer with the appropriate units. (t=?) Part B What is the inductor current at that time? Express your answer with the appropriate units.(I=?)

A 5-kW, 250-V shunt motor has an armature resistance of 0.1 ? and a field-circuit resistance...

A 5-kW, 250-V shunt motor has an armature resistance of 0.1 ? and a field-circuit resistance of 80 ?. When the motor is operating at rated voltage, the speed is observed to be 1200 r/min when the machine is loaded such that the armature current is 30 A. In order to protect both the motor and the dc supply under starting conditions, an external resistance will be connected in series with the armature winding (with the field winding remaining directly...

An LC circuit has an inductor with inductance 0.05 H and a capacitor with capacitance 5...

An LC circuit has an inductor with inductance 0.05 H and a capacitor with capacitance 5 μF. All of the energy is stored in the capacitor at t=0, and the total charge is 3×10-5 C. (a) What is the angular frequency of the oscillations in this circuit? (b) Find a mathematic equation for q(t). (c) What is the maximum current flow through the circuit? (d) How long does it take the capacitor to become completely discharged?

The circuit you’re making needs a 1.5?? capacitor but you only have three 1?? capacitors. Draw...

The circuit you’re making needs a 1.5?? capacitor but you only have three 1?? capacitors. Draw how you make an equivalent capacitor from the 1?? capacitors.

Question