Question

In: Electrical Engineering

Design an analog-digital converter circuit with OpAmp that receives a 5 Vp sinusoidal signal and a...

Design an analog-digital converter circuit with OpAmp that receives a 5 Vp sinusoidal signal and a 3.5 V trip level as input. It must deliver a TTL (Low / High) signal as output.

Solutions

Expert Solution

The Analog to Digital converter (2-bit) circuit using op-amp is designed and simulated in Multisim:

Test Case (00=0):

Test Case (01=1):

Test Case (10=2):

Test Case (11=3):

Manojponduru answered 2 years ago
Next > < Previous

Related Solutions

Design an analog-digital converter circuit with OpAmp that receives a 5 Vp sinusoidal signal and a...
Design an analog-digital converter circuit with OpAmp that receives a 5 Vp sinusoidal signal and a 3.5 V trip level as input. It must deliver a TTL (Low / High) signal as output.
discuss how analog signal is converted to a digital signal in an analog to digital (A/D)...
discuss how analog signal is converted to a digital signal in an analog to digital (A/D) converter(ADC).you may use sketches to support your answer
Design and build an 8 bit Digital to Analog Converter using the LM741 OP Amp in...
Design and build an 8 bit Digital to Analog Converter using the LM741 OP Amp in Multisim software. Analyze the system using 1000 1000, 1111 1110, and other four different byte values.
(a) For a ±10V digital-to-analog 10-bit converter, what is the analog equivalent of digital number 183?
  (a) For a ±10V digital-to-analog 10-bit converter, what is the analog equivalent of digital number 183? (b) For a ±10V digital-to-analog 10-bit converter, what is the analog equivalent of digital number 1301? (c) For a 0 − 10V analog-to-digital 10-bit converter, what is the digital equivalent of an analog 2.355V? (d) For a ±5V analog-to-digital 12-bit converter, what is the digital equivalent of an analog 4.265V?
Analog-to-Digital convertor, modified. Assume that you have a 12-bit A/D converter that can digitize an analog...
Analog-to-Digital convertor, modified. Assume that you have a 12-bit A/D converter that can digitize an analog voltage over the range of 0.00 Volts to + 3.30 Volts (just like the one in the TM4C123G). (a) What is the minimum voltage that an analog input voltage could change and be guaranteed to be detected by a change in the digital output value? E.g. in millivolts or microvolts. (b) What is the binary number that represents an analog voltage of +1.11 volts?...
Design a limiter circuit such that a ±20 V input sinusoidal wave is limited between +5...
Design a limiter circuit such that a ±20 V input sinusoidal wave is limited between +5 V and –3 V at the output. Use a single current limiting resistor and specify its value such that no diode experiences a current greater than 10 mA.
2. A digital signal processing system with analog audio signal input in the range of 0-20...
2. A digital signal processing system with analog audio signal input in the range of 0-20 Khz uses oversampling techniques and a second order sigma delta modulator to convert the analog signal into a digital bit stream at a rate of 3.072 Mhz. i) Explain how the digital bit stream may be converted in to a digital multibit stream for x(n). ii) Determine the overall improvement in signal to quantization noise ratio made possible by oversampling and noise shaping and...
(A) - sketch a 4bit R-2R ladder digital to analog converter with reference voltage,Vref=10. by using...
(A) - sketch a 4bit R-2R ladder digital to analog converter with reference voltage,Vref=10. by using thevenin theorem,derive the expression of Vout when MSB only turn 'on',LSB only turn 'on' and for an input B3B2B1B0 = 1010 and general expression for Vout (B) -- based on question (A) calculate Vout using the data in the table below Parameter Value Vref 15 V Rf 100 K ohm R 5 k ohm B3B2B1B0 1011
The circuit shown in Fig. 4.17a is a precision differential voltage-gain device. It is used to provide a single-ended input for an analog-to-digital converter. We wish to derive an expression for the output of the circuit in terms of the two inputs.
The circuit shown in Fig. 4.17a is a precision differential voltage-gain device. It is used to provide a single-ended input for an analog-to-digital converter. We wish to derive an expression for the output of the circuit in terms of the two inputs.
1. Draw a simple circuit diagram of half wave specific with sinusoidal input signal define on...
1. Draw a simple circuit diagram of half wave specific with sinusoidal input signal define on V_in (t) = A*cos(wt^2*pi*f) with peak voltage of 10 V and frequency of 60 Hz. 2. Design the output voltage in terms of fourier transform. 3. Use matlab to plot the frequency spectrum of the rectified signal for magnitude and phase use load resistance as 1 kilo-ohm and cutoff frequency as 10 Hz. 4. Design a second order butterworth filter of a specific cosine...
ADVERTISEMENT
Subjects
ADVERTISEMENT
Latest Questions
ADVERTISEMENT