Question

In: Electrical Engineering

(A) - sketch a 4bit R-2R ladder digital to analog converter with reference voltage,Vref=10. by using...

(A) - sketch a 4bit R-2R ladder digital to analog converter with reference voltage,Vref=10. by using thevenin theorem,derive the expression of Vout when MSB only turn 'on',LSB only turn 'on' and for an input B3B2B1B0 = 1010 and general expression for Vout

(B) -- based on question (A) calculate Vout using the data in the table below

Parameter Value
Vref 15 V
Rf 100 K ohm
R 5 k ohm
B3B2B1B0 1011

Solutions

Expert Solution


Related Solutions

(a) For a ±10V digital-to-analog 10-bit converter, what is the analog equivalent of digital number 183?
  (a) For a ±10V digital-to-analog 10-bit converter, what is the analog equivalent of digital number 183? (b) For a ±10V digital-to-analog 10-bit converter, what is the analog equivalent of digital number 1301? (c) For a 0 − 10V analog-to-digital 10-bit converter, what is the digital equivalent of an analog 2.355V? (d) For a ±5V analog-to-digital 12-bit converter, what is the digital equivalent of an analog 4.265V?
Design and build an 8 bit Digital to Analog Converter using the LM741 OP Amp in...
Design and build an 8 bit Digital to Analog Converter using the LM741 OP Amp in Multisim software. Analyze the system using 1000 1000, 1111 1110, and other four different byte values.
Analog-to-Digital convertor, modified. Assume that you have a 12-bit A/D converter that can digitize an analog...
Analog-to-Digital convertor, modified. Assume that you have a 12-bit A/D converter that can digitize an analog voltage over the range of 0.00 Volts to + 3.30 Volts (just like the one in the TM4C123G). (a) What is the minimum voltage that an analog input voltage could change and be guaranteed to be detected by a change in the digital output value? E.g. in millivolts or microvolts. (b) What is the binary number that represents an analog voltage of +1.11 volts?...
Design an analog-digital converter circuit with OpAmp that receives a 5 Vp sinusoidal signal and a...
Design an analog-digital converter circuit with OpAmp that receives a 5 Vp sinusoidal signal and a 3.5 V trip level as input. It must deliver a TTL (Low / High) signal as output.
Design an analog-digital converter circuit with OpAmp that receives a 5 Vp sinusoidal signal and a...
Design an analog-digital converter circuit with OpAmp that receives a 5 Vp sinusoidal signal and a 3.5 V trip level as input. It must deliver a TTL (Low / High) signal as output.
The circuit shown in Fig. 4.17a is a precision differential voltage-gain device. It is used to provide a single-ended input for an analog-to-digital converter. We wish to derive an expression for the output of the circuit in terms of the two inputs.
The circuit shown in Fig. 4.17a is a precision differential voltage-gain device. It is used to provide a single-ended input for an analog-to-digital converter. We wish to derive an expression for the output of the circuit in terms of the two inputs.
Design a buck-boost converter with a source varying from 10 to 14 V. The output voltage...
Design a buck-boost converter with a source varying from 10 to 14 V. The output voltage is regulated at – 12 V. The load varies from 10 to 15 W. The output voltage ripple must be less than 1 % for any operating condition. a) Determine the range of the duty ratio of the switch. b) Design the inductor and capacitor values used in your design. c) Confirm your solutions using a simulation software for every operating condition (you must...
A boost converter has an input voltage Vin= 10 V, switching frequency fs= 100 kHz, duty...
A boost converter has an input voltage Vin= 10 V, switching frequency fs= 100 kHz, duty ratio d=50%, load resistance RL= 20Ω, inductance 100μH, and capacitance 680 μF. If you were trying to make a boost converter enter DCM, but your load resistor could not reach Rcrit, what other controllable parameters (not including Vin) could you change to reduce the lowest value of i_L to zero? Explain your reasoning.
Create a noninverting schmitt trigger using voltage divider as it reference voltage. Designt requirement: 1. Op-amp(comparator)...
Create a noninverting schmitt trigger using voltage divider as it reference voltage. Designt requirement: 1. Op-amp(comparator) with V+ as 5V and V- connected to ground 2. Assume input is noisy voltage 3. Output should display only high and low(ground voltage values) 4. How many threshold values are there?
A buck-boost converter has an input voltage V_in= 10 V, switching frequency fs= 100 kHz, duty...
A buck-boost converter has an input voltage V_in= 10 V, switching frequency fs= 100 kHz, duty ratio d= 30%, load resistance R_L= 20Ω, inductance =100 μH, and capacitance= 680 μF. 1) Calculate the following values, and include units in your answers: a) Peak-to-peak current ripple through the inductor, Δ_iL b) Average inductor current that will cause the converter to enter DCM b) Load resistance that will cause the converter to enter DCM (R_crit) d) Average voltage across the inductor insteady-state
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT