1. Design and check for stability for a square and ground end helical spring subjected to...

1. Design and check for stability for a square and ground end helical spring subjected to a maximum force of 1300 N supported between flat surfaces. The deflection of the spring corresponding to the maximum force should be approximately 25mm. The material used for the spring is cold drawn steel wire with ultimate tensile strength, modulus of elasticity and rigidity of 1090, 207000 and 81730 MPa, respectively. Assume and state relevant parameters.

Expert Solution

samet mamat answered 2 years ago

Design a straight ended helical torsion spring for a static load 200 N-m at a deflection...

Design a straight ended helical torsion spring for a static load 200 N-m at a deflection of 45 deg with a safety factor of 1.8. Specify all parameters necessart to manufacture the spring state all assumntions. You make the following design choices: *Use unpeened oil tempered wire with 40mm long, straight ends. The coil is loaded to close it * Design safety factory Nyd=1.8 *spring index C=11 *Yield Strength Factor K=0.85 *length of the ends L1=40 mm=L2 *Material choice =...

1 A steel helical spring carries a compressive load of 32.4 pounds at a deflection of...

1 A steel helical spring carries a compressive load of 32.4 pounds at a deflection of 0.25 inches. Maximum stress is 73240psi. The spring has 1.5 end turns. Calculate the value of c for the spring of minimum volume material. Calculate the value of d and choose the nearest standard wire diameter for the actual spring. Calculate the corresponding R and the number of active coils Nc. Also, calculate the material in the spring.

4. A spring with k=45 N/m is oriented vertically with one end fixed to the ground....

4. A spring with k=45 N/m is oriented vertically with one end fixed to the ground. A 0.5 kg mass on top of the spring compresses it.   Provide a conceptual explanation of what is happing for each of the following cases a. You hold the mass while you gently compress the spring, and when you release the mass it sits at rest atop the spring. b. You place the mass on the uncompressed spring and release it. c. You drop...

A helical compression spring is wound using 1 mm-diameter music wire. The outside coil diameter of...

A helical compression spring is wound using 1 mm-diameter music wire. The outside coil diameter of the spring is 11 mm. The ends are squared and there are 12 total turns. (a) Estimate the torsional yield strength of the wire. (b) Estimate the static load corresponding to the yield strength. (c) Estimate the scale of the spring. (d) Estimate the solid length of the spring. (e) Is there any possibility for buckling?

ACCY 207 EXCEL ASSIGNMENT #2 Spring 2018 CHECK FIGURES: What If #1: NOI $630,000 &nbsp

ACCY 207 EXCEL ASSIGNMENT #2 Spring 2018 CHECK FIGURES: What If #1: NOI $630,000 Increase in NOI $180,000 REQUIREMENTS: Use the data in the posted problem for this Excel assignment. For the Year Ended December 31, 2017 prepare a Contribution Income Statement for CedarWorks using the following format for your data block page: CedarWorks For the Year Ended December 31, 2017 Operating results: Original What If #1 What If #2 What If #3 Unit selling price $3,000.00 $ $...

(1 point) A brick of mass 8 kg hangs from the end of a spring. When...

(1 point) A brick of mass 8 kg hangs from the end of a spring. When the brick is at rest, the spring is stretched by 3920 cm. The spring is then stretched an additional 2 cm and released with a downward force of F(t)=143cos(6t) NF(t)=143cos⁡(6t) N acts on it. Assume there is no air resistance. Note that the acceleration due to gravity, gg, is g=980g=980 cm/s22. Find the spring constant N/cm Set up a differential equation that describes this system....

Progress Check (Answers to Progress Checks are provided at the end of the chapter.) 5–1 Which...

Progress Check (Answers to Progress Checks are provided at the end of the chapter.) 5–1 Which of the following items is not unique to the financial statements of merchandising companies? (a) Cost of goods sold; (b) Accounts receivable; (c) Merchandise inventory. 5–2 What is a merchandising company’s gross profit? 5–3 Why are sales returns and allowances and sales discounts recorded in contrarevenue accounts instead of in the Sales account? Is this information likely to be reported outside the company? 5–4...

Using the formulas and codes provided by ACI 318 1. Design a square interior column footing...

Using the formulas and codes provided by ACI 318 1. Design a square interior column footing for a 15-in. square tied interior column that supports a dead load of 160 kips and live load of 180 kips. The column is reinforced with eight # 8 bars, also, the base of the footing is 6 ft below the grade line, the soil weight is 100 lb/ft3, the concrete weight is 150 lb/ft3, f’c = 4,000 psi, fy = 60,000 psi and...

African Burial Ground: An American Discovery (1994) Ossie Davids End Ruby Dee 1) Summarize the book,...

African Burial Ground: An American Discovery (1994) Ossie Davids End Ruby Dee 1) Summarize the book, themes, and social problem/issue 2) Identify key people and locations associated with this book 3) Identify the subject matter of the book, for example, immigration, human trafficking, interracial families, etc. 4) Provide a brief history of the subject matter ( 3-4 pages) 5) Did this book add to your knowledge of the subject matter? is so how?

design for british code 8110 1.A 500 mm square column carries a dead load of 1200...

design for british code 8110 1.A 500 mm square column carries a dead load of 1200 kN and imposed load of 400 kN. The safe bearing capacity of the soil is 180 kN/m2. Design a square pad footing to resist the loads using the following material strengths: fcu=30 N/mm2, fy=500 N/mm2. 2.Design a pad footing for a rectangular column of section 300x500 mm supporting an axial factored load of 1,400 kN. The safe bearing capacity of the soil is 180...

Question