A helical compression spring is wound using 1 mm-diameter music wire. The outside coil diameter of...

A helical compression spring is wound using 1 mm-diameter music wire. The outside coil diameter of the spring is 11 mm. The ends are squared and there are 12 total turns.

(a) Estimate the torsional yield strength of the wire.

(b) Estimate the static load corresponding to the yield strength.

(c) Estimate the scale of the spring.

(d) Estimate the solid length of the spring.

(e) Is there any possibility for buckling?

Expert Solution

samet mamat answered 2 years ago

Problem 10-3 A helical compression spring is wound using 2.5- mm -diameter music wire. The spring...

Problem 10-3 A helical compression spring is wound using 2.5- mm -diameter music wire. The spring has an outside diameter of 31 mm with plain ground ends, and 14 total coils. (a) Estimate the spring rate. (b) What force is needed to compress this spring to closure? (c) What should the free length be to ensure that when the spring is compressed solid the torsional stress does not exceed the yield strength? (d) Is there a possibility that the spring...

An as-wound helical-coil compression spring with infinite fatigue life is needed to resist a dynamic load...

An as-wound helical-coil compression spring with infinite fatigue life is needed to resist a dynamic load that varies from 8.0 to 24.0 lbf at 45.0 Hz over a dynamic deflection of 0.3 in. Because of assembly considerations, the solid length of the spring cannot be more than 1.2 in. The spring should have squared and ground ends and is to be made from peened music wire. Upon closure, use a design factor of 1.2 guarding against yielding and a fractional...

A compression spring has a diameter of 0.67 in and a coil diameter of 0.067 in,...

A compression spring has a diameter of 0.67 in and a coil diameter of 0.067 in, with 30 total coils. The spring is to be made of unpeened HD A227 wire and have squared and ground ends. Find the fatigue factor of safety when repeatedly cycled from 0 to 10.3 lbf. Use the Gerber fatigue criterion and the Zimmerli data.

1. Evaluate a music wire spring with plain ends where the wire diameter is 0.100” and...

1. Evaluate a music wire spring with plain ends where the wire diameter is 0.100” and the outer diameter is 0.600”. The desired spring rate is 100 lbf/in and the free length is 2.4”. Let the load safety factor be 1.00. a) What is the spring index, C? b) What is the total number of coils, Nt? c) What is solid length, Ls? d) What is the maximum suggested load? e) What is the maximum suggested deflection? f) What is...

A helical compression spring has 14 active coils and the free length is 12.5in. The outside...

A helical compression spring has 14 active coils and the free length is 12.5in. The outside diameter is 7/16 in and the spring has squared and ground ends. The end plates are constrained to be parallel. The material is music wire with presetting. The wire diameter is 0.042 in. Determine: (1) for static conditions compute the spring index, the solid length, the stress when the spring is compressed to the solid length. Check if static yielding occurs while the spring...

10-35: A helical coil compression spring is needed for food service machinery. The load varies from...

10-35: A helical coil compression spring is needed for food service machinery. The load varies from a minimum of 4 lbf to a maximum of 18 lbf. The spring rate k is to be 9.5 lbf/in. The outside diameter of the spring cannot exceed . The springmaker has available suitable dies for drawing 0.080-, 0.0915-, 0.1055-, and 0.1205-in-diameter wire. Use squared and ground ends, and an unpeened material. Using a fatigue design factor nf of 1.5, and the Gerber-Zimmerli fatigue-failure...

A long, fine wire is wound into a coil with inductance 5 mH. The coil is...

A long, fine wire is wound into a coil with inductance 5 mH. The coil is connected across the terminals of a battery, and the current is measured a few seconds after the connection is made. The wire is unwound and wound again into a different coil with L = 10 mH. This second coil is connected across the same battery, and the current is measured in the same way. Compared with the current in the first coil, is the...

A 0.500 mm diameter copper wire makes up a 136 turns, 7.60 cm diameter coil. There...

A 0.500 mm diameter copper wire makes up a 136 turns, 7.60 cm diameter coil. There is a magnetic field parallel to the axis of the coil. If the induced current in the coil is 2.80 A, what is the rate of change of the magnetic field? a) 0.0839 T/s b) 3.63×10-6 T/s c) 12.8 T/s d) 1.74×103 T/s

A 33 cm diameter coil consists of 19 turns of cylindrical copper wire 2.8 mm in...

A 33 cm diameter coil consists of 19 turns of cylindrical copper wire 2.8 mm in diameter. A uniform magnetic field, perpendicular to the plane of the coil, changes at a rate of 9.50

A solenoidal coil with 23 turns of wire is wound tightly around another coil with 350...

A solenoidal coil with 23 turns of wire is wound tightly around another coil with 350 turns. The inner solenoid is 25.0 cm long and has a diameter of 2.40 cm . At a certain time, the current in the inner solenoid is 0.120 A and is increasing at a rate of 1600 A/s A)For this time, calculate the average magnetic flux through each turn of the inner solenoid. Express your answer in webers. B)For this time, calculate the mutual...

Question