1 A steel helical spring carries a compressive load of 32.4 pounds at a deflection of...

1 A steel helical spring carries a compressive load of 32.4 pounds at a deflection of 0.25 inches. Maximum stress is 73240psi. The spring has 1.5 end turns. Calculate the value of c for the spring of minimum volume material. Calculate the value of d and choose the nearest standard wire diameter for the actual spring. Calculate the corresponding R and the number of active coils N_c. Also, calculate the material in the spring.

Expert Solution

samet mamat answered 1 year ago

Design a straight ended helical torsion spring for a static load 200 N-m at a deflection...

Design a straight ended helical torsion spring for a static load 200 N-m at a deflection of 45 deg with a safety factor of 1.8. Specify all parameters necessart to manufacture the spring state all assumntions. You make the following design choices: *Use unpeened oil tempered wire with 40mm long, straight ends. The coil is loaded to close it * Design safety factory Nyd=1.8 *spring index C=11 *Yield Strength Factor K=0.85 *length of the ends L1=40 mm=L2 *Material choice =...

An as-wound helical-coil compression spring with infinite fatigue life is needed to resist a dynamic load...

An as-wound helical-coil compression spring with infinite fatigue life is needed to resist a dynamic load that varies from 8.0 to 24.0 lbf at 45.0 Hz over a dynamic deflection of 0.3 in. Because of assembly considerations, the solid length of the spring cannot be more than 1.2 in. The spring should have squared and ground ends and is to be made from peened music wire. Upon closure, use a design factor of 1.2 guarding against yielding and a fractional...

3. Determine the effective spring constant of the following sandwiches of materials under compressive load (determine...

3. Determine the effective spring constant of the following sandwiches of materials under compressive load (determine the material spring constant only). The material sandwiches are being held in place by a ½-13 UNC bolt, nut, and flat washers on both sides. The first and third materials listed in each sandwich are 0.4” thick and the middle material is 0.04” thick, together making a 0.84” thick sandwich a. Aluminum, copper-asbestos, steel b. Steel, copper, steel c. Steel, rubber, steel d. Steel,...

A spring with a spring rate of 75 lb/in has a working deflection of 1 in....

A spring with a spring rate of 75 lb/in has a working deflection of 1 in. It provides a minimum of 150 lb at installation. The spring is formed from 0.25 in diameter unpeened music wire. The coil has squared and ground ends, and it fits in a 2.1 in diameter hole with 0.1 in clearance. Assuming a 15% clash allowance, find: a) Safety factor for infinite life in fatigue b) Shut height c) Safety factor at shut height d)...

10-35: A helical coil compression spring is needed for food service machinery. The load varies from...

10-35: A helical coil compression spring is needed for food service machinery. The load varies from a minimum of 4 lbf to a maximum of 18 lbf. The spring rate k is to be 9.5 lbf/in. The outside diameter of the spring cannot exceed . The springmaker has available suitable dies for drawing 0.080-, 0.0915-, 0.1055-, and 0.1205-in-diameter wire. Use squared and ground ends, and an unpeened material. Using a fatigue design factor nf of 1.5, and the Gerber-Zimmerli fatigue-failure...

(1 point) A hollow steel ball weighing 4 pounds is suspended from a spring. This stretches...

(1 point) A hollow steel ball weighing 4 pounds is suspended from a spring. This stretches the spring 1/6 feet. The ball is started in motion from the equilibrium position with a downward velocity of 4 feet per second. The air resistance (in pounds) of the moving ball numerically equals 4 times its velocity (in feet per second) . Suppose that after t seconds the ball is y feet below its rest position. Find y in terms of t. (Note...

steel structure Q1. The column carries 60 kips dead load and 40 kips live load, its...

steel structure Q1. The column carries 60 kips dead load and 40 kips live load, its length is 20 ft, and the steel is A992. Assume the member as pinned at the top and bottom. (a) Compute Pa; (b) Determine the effective length (KL); (c) Use ASD method to select the lightest W section; (d) Check the local buckling slenderness limits of the selected section.

Determine the allowable axial compressive load for a 25-foot long A992 W8X40 structural steel column using...

Determine the allowable axial compressive load for a 25-foot long A992 W8X40 structural steel column using the AISC procedure as indicated in your textbook. The bottom of the column is fixed, an the top is pinned. Use the material properties and dimensions as indicated in the appendices of your textbook. 250.3k 131.4k 215.8k 283.4k

1. Design and check for stability for a square and ground end helical spring subjected to...

1. Design and check for stability for a square and ground end helical spring subjected to a maximum force of 1300 N supported between flat surfaces. The deflection of the spring corresponding to the maximum force should be approximately 25mm. The material used for the spring is cold drawn steel wire with ultimate tensile strength, modulus of elasticity and rigidity of 1090, 207000 and 81730 MPa, respectively. Assume and state relevant parameters.

in table 1 the failure load obtained from the compressive strength test at the laboratory are presented....

in table 1 the failure load obtained from the compressive strength test at the laboratory are presented. sate whether those values are satisfactory according to TS EN206 1;2004 or not verify your results. concrete class C35. Determine also standard deviation and variance Table 1 Failure load for 200 mm cubic samples NO FAILURE LOAD (KN) 1 1645 2 1646 3 1641 4 1641 5 1641 PLEASE CAN YOU SLOVE IT STEP BY STEP

Question