A 1200 kW, 550 V DC generator has a terminal voltage of 500 V at rated...

A 1200 kW, 550 V DC generator has a terminal voltage of 500 V at rated current. It is being driven at a speed of 400 rpm. The armature resistance is 0.0009 Ω.
a. Determine the armature voltage.
b. Determine the developed torque.
c. Determine the armature copper loss.

Expert Solution

Manojponduru answered 2 years ago

Which type of DC generator has best voltage regulation?

The constant-speed magnetization curve for a 25-kW, 250-V dc machine at a speed of 1200 r/min...

The constant-speed magnetization curve for a 25-kW, 250-V dc machine at a speed of 1200 r/min is shown in figure below. This machine is separately excited and has an armature resistance of 0.14 Ω. This machine is to be operated as a dc generator while driven from a synchronous motor at constant speed. a. What is the rated armature current of this machine? b. With the generator speed held at 1200 r/min and if the armature current is limited to...

A 500 nF capacitor is initially connected to a 100 V DC voltage source. At some...

A 500 nF capacitor is initially connected to a 100 V DC voltage source. At some long time later, the switch is flipped and the capacitor is now connected to a 120 mH inductor. a) What is the frequency of oscillation in the circuit after the switch is flipped. b) After the switch is filpped, what would the peak current value be? c) What is the maximum possible value for the energy stored in the inductor? d) The energy in...

identify that parts of a dc generator that convert its induced voltage into a dc output

An electric motor has the power P = 45 kW with terminal voltage Ueff = 380...

An electric motor has the power P = 45 kW with terminal voltage Ueff = 380 V. The power factor is cos (φ) = 0.85. a) Explain the concept of the power factor! What is it? b) Calculate the apparent power S, reactive power Q, and the currents Ieff, IW (active current) and IB (reactive current)! c) What are the consequences for producers and consumers from the existence of reactive power or reactive current?

Problem: A PM DC motor has the following parameters: Rated Power 10 hp; Rated armature voltage...

Problem: A PM DC motor has the following parameters: Rated Power 10 hp; Rated armature voltage 230 V-DC; Rated RPM: 1800; Armature Resistance: 0.2 Ohm Armature Inductance: 0.005 H Inertia (motor plus mechanical load): 0.1 kgm^2; Viscous friction coefficient: 0.015 Nms 1. Compute the voltage constant of the motor. Also compute the rated current and rated torque of the motor (obtained at the rated RPM). If the motor is supplied by 230 V across the armature, and the only torque...

A 400 V dc shunt motor has a rated armature current of 76 A at a...

A 400 V dc shunt motor has a rated armature current of 76 A at a speed of 1000 rpm. The armature resistance of the motor is 0.4ohm, the field resistance is 100 ohm, and the rotational losses are 0.9 kW. The load of the motor is bidirectional. Calculate the following: (a) No-load speed of the motor. (b) Motor speed, where the armature current is 60 A during regenerative braking. (c) Developed torque during regenerative braking. (d) Back electromotive force,...

The terminal voltage across a single phase of a stepper motor used as a generator is...

The terminal voltage across a single phase of a stepper motor used as a generator is applied across a load resistor of 33 ohms. This terminal voltage has an amplitude of 18.7V and a frequency of 242 Hz. From a previous measurement, we know that this stepper motor phase has an internal resistance of 11.2 ohms. What is the time-averaged power delivered to the load? What is the electrical efficiency of this circuit? Write down an expression for the instantaneous...

An ac generator has a frequency of 7.5 kHz and a voltage of 35 V. When...

An ac generator has a frequency of 7.5 kHz and a voltage of 35 V. When an inductor is connected between the terminals of this generator, the current in the inductor is 30 mA. What is the inductance of the inductor?

A generator with an rms voltage of 130 V is connected in series to a resistor...

A generator with an rms voltage of 130 V is connected in series to a resistor 3.65 kΩ and a capacitor 3.00 μF . 1. At what frequency must this circuit be operated for the current to lead the voltage by 29.0 ∘? (Answer Hz) 2. Using the frequency found in part A, find the average power consumed by this circuit. (Answer in W) ------------------------------------------ A 1.6-m wire is wound into a coil with a radius of 3.2 cm. 1....

Question