Question

In: Mechanical Engineering

One kilogram of water in a piston-cylinder assembly undergoes the two internally reversible processes in series....

One kilogram of water in a piston-cylinder assembly undergoes the two internally reversible processes in series. P1 = 0.1 MPa, T1 = 100C, s1 = s2​ = 7.3164 kJ/kg*K​, P2 = 0.5 MPa, T2 = T3, P3 = 1.5 MPa, and u1 = 2506.7 kJ/kg. Find T2. Legibly show and explain all work, units, and formulas.

Solutions

Expert Solution

samet mamat answered 2 years ago
Next > < Previous

Related Solutions

Carbon monoxide gas (CO) contained within a piston– cylinder assembly undergoes three processes in series: Process...
Carbon monoxide gas (CO) contained within a piston– cylinder assembly undergoes three processes in series: Process 1–2: Expansion from p1 = 4.5 bar, V1 = 0.8 m3 to V2 = 1.4 m3, during which the pressure-volume relationship is pV = constant. Process 2–3: Constant-volume heating from state 2 to state 3, where p3 = 4.5 bar. Process 3–1: Constant-pressure compression to the initial state. Evaluate the overall work, in kJ and graph
One kilogram of water is contained in a piston-cylinder device at 100 degC. The piston rests...
One kilogram of water is contained in a piston-cylinder device at 100 degC. The piston rests on lower stops such that the volume occupied by the water is 0.835 m3. The cylinder is fitted with an upper set of stops. When the piston rests against the upper stops, the volume enclosed by the piston-cylinder device is 0.841 m3. A pressure of 200 kPa is required to support the piston. Heat is added to the water until the water exists as...
One kilogram of boiling water is vaporized to steam at 100 kPa in a frictionless piston-and-cylinder...
One kilogram of boiling water is vaporized to steam at 100 kPa in a frictionless piston-and-cylinder device. Using the Steam Tables, answer the following: Is the heat needed to vaporize the water to steam equal to the change in enthalpy? Or TDS? To calculate the work done by the steam, is the first law of thermodynamics equation or the general equation for work applicable? Is the entropy generation equal to the change in entropy of the water? Does the heat...
A piston–cylinder device contains steam that undergoes a reversible thermodynamic cycle. Initially the steam is at...
A piston–cylinder device contains steam that undergoes a reversible thermodynamic cycle. Initially the steam is at 400 kPa and 350oC with a volume of 0.3 m3. The steam is first expanded isothermally to 150 kPa, then compressed adiabatically to the initial pressure, and finally compressed at the constant pressure to the initial state. Determine (a) the net work and heat transfer for the cycle after you calculate the work and heat interaction for each process and (b) show the cyclic...
A gas in a piston–cylinder assembly undergoes a compression process for which the relation between pressure...
A gas in a piston–cylinder assembly undergoes a compression process for which the relation between pressure and volume is given by pVn = constant. The initial volume is 0.2 m3, the final volume is 0.04 m3, and the final pressure is 2 bar. For n = 1.3, determine the initial pressure, in bar, and the work for the process, in kJ.
Water in a piston-cylinder assembly is at 1 MPa, 500◦C. There are two stops, a lower...
Water in a piston-cylinder assembly is at 1 MPa, 500◦C. There are two stops, a lower one at which Vmin = 1 m3 and an upper one at Vmax = 3 m3. The piston is loaded with a mass and outside atmosphere such that it floats when the pressure is 500 kPa. This setup is now cooled to 100◦C by rejecting heat to the surroundings at 20◦C. a. Show the path of the process on T-V and P-V diagrams. b....
Air undergoes a polytropic process in a piston–cylinder assembly from p1 = 1 bar, T1 =...
Air undergoes a polytropic process in a piston–cylinder assembly from p1 = 1 bar, T1 = 295 K to p2 = 7 bar. The air is modeled as an ideal gas and kinetic and potential energy effects are negligible. For a polytropic exponent of 1.4, determine the work and heat transfer, each in kJ per kg of air, (1) assuming constant cv evaluated at 300 K. (2) assuming variable specific heats.
Air undergoes a polytropic process in a piston–cylinder assembly from p1 = 1 bar, T1 =...
Air undergoes a polytropic process in a piston–cylinder assembly from p1 = 1 bar, T1 = 295 K to p2 = 3 bar. The air is modeled as an ideal gas and kinetic and potential energy effects are negligible. For a polytropic exponent of 1.2, determine the work and heat transfer, each in kJ per kg of air, (1) assuming constant cv evaluated at 300 K. (2) assuming variable specific heats.
Air undergoes a polytropic process in a piston–cylinder assembly from p1 = 1 bar, T1 =...
Air undergoes a polytropic process in a piston–cylinder assembly from p1 = 1 bar, T1 = 295 K to p2 = 3 bar. The air is modeled as an ideal gas and kinetic and potential energy effects are negligible. For a polytropic exponent of 1.6, determine the work and heat transfer, each in kJ per kg of air, (1) assuming constant cv evaluated at 300 K. (2) assuming variable specific heats.
One kg of water in a piston-cylinder assembly, initially at 1.5 bar and 200 C, cools...
One kg of water in a piston-cylinder assembly, initially at 1.5 bar and 200 C, cools at constant pressure with no internal irreversibilities to a final state where the water is a saturated liquid. For the water as the system, determine the work, the heat transfer, and the amounts of exergy transfer accompanying work and heat transfer, each in kJ. Let T0 = 20 °C, p0=1 bar and ignore the effects of motion and gravity. THERE ARE SOME DIFFERENT ANSWERS...
ADVERTISEMENT
Subjects
ADVERTISEMENT
Latest Questions
ADVERTISEMENT