Question

In: Mechanical Engineering

A steel alloy specimen having a rectangular cross section of dimensions 19.1 mm × 3.0 mm...

A steel alloy specimen having a rectangular cross section of dimensions 19.1 mm × 3.0 mm (0.7520 in. × 0.1181 in.) has the stress-strain behavior shown in the Animated Figure 6.22. If this specimen is subjected to a tensile force of 95120 N (21380 lbf) then (a) Determine the amount of elastic strain induced. (b) Determine the amount of plastic strain induced. (c) If its original length is 590 mm, what will be its final length after this force is applied and then released? The elastic modulus for steel is 207 GPa.

Solutions

Expert Solution


Related Solutions

The steel beam has the cross section shown. The beam length is L = 6.9 m, and the cross-sectional dimensions are d = 345 mm, bf = 185 mm, tf = 15 mm, and tw = 10 mm.
The steel beam has the cross section shown. The beam length is L = 6.9 m, and the cross-sectional dimensions are d = 345 mm, bf = 185 mm, tf = 15 mm, and tw = 10 mm. Calculate the largest intensity of distributed load w0 that can be supported by this beam if the allowable bending stress is 185 MPa.
A beam of steel having square cross section of 20x20mm2 having E = 200 GPa is...
A beam of steel having square cross section of 20x20mm2 having E = 200 GPa is subjected to an axial (P) load of 20 kN, Torsional (T) load of 60 Nm and Transverse (F) load of 0.60 kN as shown in Figure. Solve each load independently for both element A and B existing at the top and side surface of the beam respectively and determine: a) State of stress against each load condition for both element A and B b)...
A rectangular cross section beam (A) made of steel constructed in an industrial building between two...
A rectangular cross section beam (A) made of steel constructed in an industrial building between two columns which are “X” m apart. The beam is acting as a support for one end of a pair of crane wheel (B). The distance b/w wheels are “Y” m. The crane is used to lift max. of Z tonnes of load which is having hook at the centre of crane. Draw shear force and B.M diagram of the beam. Case i) If the...
A rectangular cross section beam (A) made of steel constructed in an industrial building between two...
A rectangular cross section beam (A) made of steel constructed in an industrial building between two columns which are “X” m apart. The beam is acting as a support for one end of a pair of crane wheel (B). The distance b/w wheels are “Y” m. The crane is used to lift max. of Z tonnes of load which is having hook at the centre of crane. Draw shear force and B.M of all types of beam diagram of the...
A rectangular cross section beam (A) made of steel constructed in an industrial building between two...
A rectangular cross section beam (A) made of steel constructed in an industrial building between two columns which are “X” m apart. The beam is acting as a support for one end of a pair of crane wheel (B). The distance b/w wheels are “Y” m. The crane is used to lift max. of Z tonnes of load which is having hook at the centre of crane. Draw shear force and B.M diagram of the beam. Case i) If the...
1-. A concrete beam of rectangular cross section of size 300mm x 500 mm is prestressed...
1-. A concrete beam of rectangular cross section of size 300mm x 500 mm is prestressed with 750kN at an eccentricity of 100mm from the centre of gravity of the gross section with 500 mm2 of prestressing steel stress to 1500 N/mm2. Analyse the section for stress (find the stress in concrete at top and bottom fibre) 2- The same concrete is covering a span of 7m. It is subjected to live load of 20 kN/m. Evaluate the stresses at...
A 2024-T3 aluminum bar has rectangular cross section dimensions of 2" x 0.5". The length of...
A 2024-T3 aluminum bar has rectangular cross section dimensions of 2" x 0.5". The length of the column is 9.0 inches. A) Calculate the transition slenderness ratio (Sr)D for this column. [Answer should be 69.9] B) Calculate the slenderness ratio for your assigned column length. [Answer should be 62] C) Calculate the maximum unit load (Pcr/A) for the bar. Indicate whether the column is a Johnson or Euler column. [Numerical answer should be 25296 psi but I don't know Johnson...
A cylindrical specimen of some metal alloy 8.6 mm in diameter is stressed in tension. A...
A cylindrical specimen of some metal alloy 8.6 mm in diameter is stressed in tension. A force of 9070 N produces an elastic reduction in specimen diameter of 0.0048 mm. Calculate the elastic modulus (in GPa) of this material if its Poisson's ratio is 0.33.
In a rectangular cross-section canal with a width of 10 m and a depth of 1.5...
In a rectangular cross-section canal with a width of 10 m and a depth of 1.5 m, uniform and Continuous current monitoring is applied. The channel's Manning coefficient includes 0.015. Base because its slope is 0.0005. Considering this information a) By writing the numerical magnitude of water face slope and energy line slope and its rationale Set. b) Calculate the speed of the current in the channel. c) Calculate the flow of the current in the channel. d ) When...
A direct shear test is conducted on a large specimen of dry sand (square cross section...
A direct shear test is conducted on a large specimen of dry sand (square cross section with following dimensions: 7.5 cm x 7.5 cm x 3.0 cm [height], Mass = 271.0 g) with a normal stress of 500 kPa. Failure occurred when the horizontal force was 1.96 kN. For the same sand, tests were also conducted to determine the specific gravity and the maximum and minimum void ratios. These tests yielded the following results: Gs= 2.65, emax=0.80, emin = 0.45....
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT