In a rectangular cross-section canal with a width of 10 m and a depth of 1.5...

In a rectangular cross-section canal with a width of 10 m and a depth of 1.5 m, uniform and

Continuous current monitoring is applied. The channel's Manning coefficient includes 0.015. Base

because its slope is 0.0005. Considering this information

a) By writing the numerical magnitude of water face slope and energy line slope and its rationale

Set.

b) Calculate the speed of the current in the channel.

c) Calculate the flow of the current in the channel.

d ) When a discharge is applied to the channel, the effect of the discharge is opposite from the discharge point to the current direction.

by writing the reasoning whether it can be observed in the direction (on the membrane of the current)

You calculate.

Expert Solution

Ally Wells answered 7 months ago

An irrigation canal with trapezoidal cross-section has the following elements: bottom width = 2m, depth of...

An irrigation canal with trapezoidal cross-section has the following elements: bottom width = 2m, depth of water = 0.9m, side slope 1.5H to 1V, slope of canal bed = 0.001, n = 0.025. The canal will serve clay-loam rice land. What is the hydraulic radius in meters? What is the mean velocity in m/s? If the canal will serve a clay-load rice land, determine the area in hectares it can serve if the duty of water per hectare is 3L/s.

A wire of length L has a rectangular cross-section with height H and width W. The...

A wire of length L has a rectangular cross-section with height H and width W. The wire has a hole all the way through it of area a. The wire is made of material with constant resistivity ρ1 . A battery with a known voltage is applied across the ends of the wire. a. Find the electric field inside the material and the current flowing through the wire. b. If the hole is totally filled with a material that has...

A beam with a cross-section of 0.3 m x 0.7 m has an effective depth of...

A beam with a cross-section of 0.3 m x 0.7 m has an effective depth of 0.638 m and a span of 4.30 m. Use the following data below to determine (a) the steel requirement due to flexure, (b) ultimate threshold torsion, and (c) spacing of stirrup due to combined shear and torsion: Mu = 322 KN-m Vu = 317 KN Tu = 42 KN-m f'c =28 MPa fyt = 414 MPa 12 mm stirrup diameter cover of 0.04 m

A square foundation 1.5? × 1.5? is founded at a depth of 1.5 m below the...

A square foundation 1.5? × 1.5? is founded at a depth of 1.5 m below the ground surface in sand soil having a cohesion ? ′ = 0 ?? ?2 ⁄ and angle of shearing resistance∅ ′ = 33° . The water table is at a depth of 6 m below ground level. The unit weight of soil above the water table is ? = 18 ?? ?3 ⁄ and the saturated unit weight of the soil ???? = 19...

A rectangular beam has a width of 300 mm and an effective depth of 510 mm....

A rectangular beam has a width of 300 mm and an effective depth of 510 mm. It carries Vu = 200 KN and Mu = 55 KN-m and is reinforced with 2650 mm2. Use f’c = 21 MPa and fy = 345 MPa. Normal concrete. Express your answer in two decimal places. a. Compute the shear strength in KN provided by concrete using the less conservative formula as shown. Express your answer in two decimal places. b. Calculate the required...

Calculate the flow depth in a rectangular riveted steel open channel with a width of 6.1...

Calculate the flow depth in a rectangular riveted steel open channel with a width of 6.1 m and a slope of 0.0001, since the water flow is 6.8 m3/s.

The rectangular hollow section in this welded assembly has a height of h=73mm, a width of...

The rectangular hollow section in this welded assembly has a height of h=73mm, a width of w=48mm and a length L=592mm. For the weld in this assembly, calculate either the Unit second polar moment of Area or the Unit Second Moment of Area, whichever is required to determine the secondary shear stress for this weld loading condition. Provide your answer in m3.

Determine the limiting values of the width a of a waveguide of square cross section which...

Determine the limiting values of the width a of a waveguide of square cross section which will transmit a wave of length lambda in the TE10 mode but not in the TE11 or TM11 modes.

Design a canal having a trapezoidal cross section to carry a design discharge of irrigation water...

Design a canal having a trapezoidal cross section to carry a design discharge of irrigation water of 900 cfs. The slope of the canal is to be 0.002. The canal is to be lined with concrete, and it is to have the best hydraulic section for the design flow. Adopt a Manning’s roughness coefficient ? for lined canals under (troweled concrete) ? = 0.012.

Compute the normal depth (y) in a trapezoidal channel having a bottom-width 10 m, side slopes...

Compute the normal depth (y) in a trapezoidal channel having a bottom-width 10 m, side slopes 1H to 1V and carrying a flow of 30 m3/s. The slope of the channel bottom is So = 0.001 and n = 0.013. A. B. C. D.

Question