A test was conducted on a 4-stroke four cylinder engine having 6.9 cm diameter and 8.9...

A test was conducted on a 4-stroke four cylinder engine having 6.9 cm diameter and 8.9 cm stroke. The fuel supply to the engine is 0.065 kg/min. The B.P measurements are given below with constant engine speed of 300 rpm: With all cylinder firing = 16.9 kW Cut off at 1st cylinder = 8.46 kW Cut off at 2nd cylinder = 8.56 kW Cut off at 3rd cylinder = 8.6 kW Cut off at 1st cylinder = 8.46 kW If clearance volume is 70 cm3 then find the mechanical efficiency, Indicate Power, Indicated thermal efficiency, Indicated mean effective pressure and also comment about the engine type whether it is SI or CI? Take Calorific value of fuel = 43500 kJ/kg

Expert Solution

samet mamat answered 1 year ago

A 4 cylinder 4 stroke 2.3 L diesel engine with bore = 12.4 cm and stroke...

A 4 cylinder 4 stroke 2.3 L diesel engine with bore = 12.4 cm and stroke =11 cm. the crank radius is 6.2 cm and with a connecting rod length 15 cm. the compression ratio of the engine is 20 and the combustion efficiency is 97.3 %. If the average speed of the car over the running life of the engine is 56 km/h and the total traveled distance of the engine is 250000 km. note: use the engine speed...

1) A four-stroke diesel engine has a piston diameter of 16.5 cm and a stroke of...

1) A four-stroke diesel engine has a piston diameter of 16.5 cm and a stroke of 27 cm. The compression ratio is 14.3, the cut-off 4.23% of the stroke and the mean effective pressure 4.12 bar. The engine speed is 264 rev/min and the fuel consumption is 1.076 kg of oil per hour, having a calorific value of 39150 kJ/kg. Calculate the relative efficiency of the engine 2). A diesel engine has a brake thermal efficiency of 30%. If the...

A single-cylinder, four stroke research engine operates on Otto cycle. The specification of the engine is...

A single-cylinder, four stroke research engine operates on Otto cycle. The specification of the engine is shown as below:- Displacement volume of the cylinder = 540 cm3 Clearance volume of the cylinder = 60 cm3 Minimum temperature = 200°C Minimum pressure = 200 kPa Net work output = 1000 kJ/kg Sketch the process on a P-V diagram and by using constant specific heat at room temperature, determine: i) the temperature and pressure at each process, ii) the thermal efficiency of...

A two-cylinder, four-stroke gas engine has a bore of 380 mm and a stroke of 585...

A two-cylinder, four-stroke gas engine has a bore of 380 mm and a stroke of 585 mm. At 240 rev/min the torque developed is 11.86 kNm. If the engine is supplied with a mixture of gas and air in the proportion of 1 to 7 by volume. The estimated volumetric efficiency is 85% and the Qnet,p of the gas is 38.6 MJ/m3. Calculate the brake thermal efficiency of the engine.

A four-cylinder four-stroke engine is operating at a bmep of 2 bar. The pressure at inlet...

A four-cylinder four-stroke engine is operating at a bmep of 2 bar. The pressure at inlet valve closure is 0.37 bar, and the fmep is 0.8 bar. Assuming that the engine gross indicated efficiency is unchanged, verify that disablement of the valves on two cylinders would reduce the fuel consumption by about 13 per cent compared with about an 8 per cent fuel saving if the fuel was not supplied to two cylinders. Assume that the gross imep is proportional...

1. An aluminum air-cooled engine cylinder head for a single cylinder, 2-stroke engine is to be...

1. An aluminum air-cooled engine cylinder head for a single cylinder, 2-stroke engine is to be die-cast. The overall diameter of the cylinder head is 101.6 mm. If the projected plan area of the runners and gating system is 100 mm2 and the casting pressure is 10 MPa (1500 psi), what minimum locking force is required for the die-casting machine in kN.

12. Design a cast iron flywheel having six arms for a four stroke engine developing 120...

12. Design a cast iron flywheel having six arms for a four stroke engine developing 120 kW at 150 r.p.m. The mean diameter of the flywheel may be taken as 3 metres. The fluctuation of speed is 2.5% of mean speed. The workdone during the working stroke is 1.3 times the average workdone during the whole cycle. Assume allowable shear stress for the shaft and key as 40 MPa and tensile stress for cast iron as 20 MPa. The following...

A tube 12 cm in diameter is carrying engine oil a distance of 4 meters from...

A tube 12 cm in diameter is carrying engine oil a distance of 4 meters from barrel to outlet. If the pressure difference between the ends of the tube is 1064.28 atm , what is the oil flow rate?

During the power stroke in a four-stroke automobile engine, the pis-ton is forced down as the...

During the power stroke in a four-stroke automobile engine, the pis-ton is forced down as the mixture of combustion products and air undergoes an adiabatic expansion. Assume (1) the engine is running at 2500 cycles/min; (2) the pressure immediately before the expansion is 20.0 atm; (3) the volumes of the mixture immediately before and after the expansion are 50.0 cm3and 400 cm3, respectively ; (4) the time interval for expansion is one-fourth that of the total cycle; and (5) the...

An ideal four stroke Otto cycle engine has 6 cylinders and a displacement of 4 Liters....

An ideal four stroke Otto cycle engine has 6 cylinders and a displacement of 4 Liters. It has a compression ratio of 8.5:1. If the mean effective pressure is 4000 kPa when operating at 3000 rpm, what will be the indicated power and what is the required heat transfer to the engine from a combusting fuel?

Question