Question

In: Electrical Engineering

Design a 4 th order band-pass, maximally flat lumped-element filter with center frequency 3 GHz and...

Design a 4 th order band-pass, maximally flat lumped-element filter with center frequency 3 GHz and 10% bandwidth. The characteristic impedance is 50 Ω.

FR4 substrate εr = 4.4, d = 1.6 mm, and tan δ = 0.02, with copper conductors 17 μm thick.

Solutions

Expert Solution

Manojponduru answered 2 years ago
Next > < Previous

Related Solutions

Butterworth filter a)Design a 5th order low pass Butterworth low-pass filter with a cut-off frequency of...
Butterworth filter a)Design a 5th order low pass Butterworth low-pass filter with a cut-off frequency of 1592 Hz and a dc gain of 3dB. Find and present the mathematical transfer function of the filter, showing all your steps. b) Write a Matlab code to plot the magnitude of this function with a linear scale in dB units on the ordinate, and a log scale of frequency on the abscissa. The plot range should be: ordinate- linear scale from -100dB to...
Part 5 The frequency response of RLC circuits : Design a passive filter: Band Pass, ISM...
Part 5 The frequency response of RLC circuits : Design a passive filter: Band Pass, ISM Band 433.050 MHz to 434.790 MHz . Prepare a report to describe your design. Your results should include the following : i. Simulation of the designed filters by using any simulation software. ii. Attach a 1 kΩ resistor as a load to the initial design of your filter. Explain how the transfer function change. Does the type of filter change? Does the cut-off frequency...
Design a second-order band-pass filter using resistors and capacitors for a microphone for a hearing aid,...
Design a second-order band-pass filter using resistors and capacitors for a microphone for a hearing aid, which allows signals in the range of 1 to 16 kHz to pass through. For the component values that you chose, at what frequency is the transfer function at a maximum?
Design and simulate a first order low pass filter so that it has a cutoff frequency...
Design and simulate a first order low pass filter so that it has a cutoff frequency of 2 kHz and a passband gain of 1. please use online multisim
Design and simulate a first order high pass filter so that it has a cutoff frequency...
Design and simulate a first order high pass filter so that it has a cutoff frequency of 2 kHz and a passband gain of 1. please use online multisim
Design and build an active second order low pass filter with cut off frequency of 8kHz...
Design and build an active second order low pass filter with cut off frequency of 8kHz using opamp -Show circuit diagram -Show input voltage and frequency - Show all calculations and placement of indicator to measure output frequency to measure cut off
Design and build an active second order low pass filter with cut off frequency of 8kHz...
Design and build an active second order low pass filter with cut off frequency of 8kHz -Show circuit diagram -Show input voltage and frequency - Show all calculations and placement of indicator to measure output frequency to measure cut off
Design a wide band pass filter with fL = 500 Hz, fH = 2kHz and a...
Design a wide band pass filter with fL = 500 Hz, fH = 2kHz and a pass band gain of 10.
Design a first order, high pass active filter with a cutoff frequency of 20 krad/sec. Cascade...
Design a first order, high pass active filter with a cutoff frequency of 20 krad/sec. Cascade Four of this filter designed and find reasonable values for the resistor and capacitor. Obtain the transfer function and show a circuit schematic for your filter. Plot the Bode plot
Design a 3-pole Butterworth low-pass filter with a DC gain of 5 and a -3db frequency...
Design a 3-pole Butterworth low-pass filter with a DC gain of 5 and a -3db frequency of 550Hz. design should use capacitors of the following values: 0.01uf, 0.022uf, 0.033uf, 0.047uf, 0.056uf, 0.1uf, 0.22uf, and 1uf.
ADVERTISEMENT
Subjects
ADVERTISEMENT
Latest Questions
ADVERTISEMENT