(c) Draw a schematic graph of resolved shear stress versus shear strain for a single crystal...

(c) Draw a schematic graph of resolved shear stress versus shear strain for a single crystal of a pure metal. Clearly label the point of the critical resolved shear stress and the three subsequent stages of dislocation behaviour. Describe these three stages.

(d) Explain why the critical resolved shear stress is much lower than the theoretical strength, based on the force required to break atomic bonds within the structure.

Expert Solution

samet mamat answered 2 years ago

Determine the critical resolved shear stress for an iron crystal which deforms by simultaneous slip on...

Determine the critical resolved shear stress for an iron crystal which deforms by simultaneous slip on (110) [111], (110) [111], (110)[111], and (110) [111] when the tensile stress along [010] is 95.2 MPa. {Manual calculations perfectly OK. But it would be good to do this on a spreadsheet.}

Plot schematic stress strain diagram for composite material. Show each stage in the graph and explain...

Plot schematic stress strain diagram for composite material. Show each stage in the graph and explain them.

define the terms - Shear strain in shaft - Shear stress in shaft - Polar moment...

define the terms - Shear strain in shaft - Shear stress in shaft - Polar moment of inertia - Polar section modulus - Torsion rigidity -torsion

For each of the following pairs of polymers, plot and label schematic stress-strain curves on the...

For each of the following pairs of polymers, plot and label schematic stress-strain curves on the same graph [i.e. make separate plots for parts (a), (b) and (c)]. (a) Polychloroprene rubber having a number-average molecular weight of 100,000 g/mol and 15% of available sites cross-linked; liner polypropylene having a number-average molecular weight of 150,000 g/mol.

Sketch example stress strain curves for the following material properties (2 curves on each graph): Graph...

Sketch example stress strain curves for the following material properties (2 curves on each graph): Graph 1: Brittle and Ductile Graph 2: strong and weak (relative) Graph 3: Non-linear and linear material

Consider a single crystal of a cubic metal that is subjected to a tensile stress along...

Consider a single crystal of a cubic metal that is subjected to a tensile stress along the [0 1 2 ] direction. Calculate the Schmidt factor for the following slip systems. In each case sketch the tensile axis as well as the slip plane and slip direction. a) (0 -1 1) [0 1 1] b) (1 0 1) [-1 -1 1] c) (0 1 0) [ -1 0 1 ] d) If the crystal above is subjected to an increasing...

The figure shows an approximate plot of stress versus strain for a spider-web thread, out to...

The figure shows an approximate plot of stress versus strain for a spider-web thread, out to the point of breaking at a strain of 2.05. The vertical axis scale is set by a = 0.130 GN/m2,b = 0.460 GN/m2, and c = 0.840 GN/m2. Assume that the thread has an initial length of 0.780 cm, an initial cross-sectional area of 8.00 × 10-12 m2, and (during stretching) a constant volume. The strain on the thread is the ratio of the...

Graph 2 Substance Ammonia This is an hypothetic Refrigeration cycle. Draw the schematic for this case....

Graph 2 Substance Ammonia This is an hypothetic Refrigeration cycle. Draw the schematic for this case. (evaporator, compressors ...) Sketch the T-s and P-v diagram. 30 points. Process State 1 leaving the evaporator at -20 C and 175 kPa State 2 leaving the Low pressure isentropic compressor at 5.5 bar and enter the high pressure irreversible compressor to state 3 State 3 135 C, 20 bar State 4 isobaric condenses process (3-4) to saturated liquid State 5 (4-5) expansion valve...

Using this table, please fill the table, draw the stress strain curve and then answer the...

Using this table, please fill the table, draw the stress strain curve and then answer the question. In case where the load is released at point 1 and 2 Draw and show the permanent and the recovery deformations. 0 1 2 3 Force 0 Kn 400 Kn 650 Kn 550 Kn Length 2 cm 2.004 cm 2.036 cm 2.049 cm Diameter 1 cm 0.9995 cm 0.998 cm 0.996 cm ∆L/L ∆d/d ᵋx ᵋz Calculate the Yield stress in the wire...

DISCUSSIONS: 1. Draw a typical stress-strain diagram and indicate what are meant by peak strength and...

DISCUSSIONS: 1. Draw a typical stress-strain diagram and indicate what are meant by peak strength and residual strength . 2. What are the limitations of direct shear stress? 3. Draw the Mohr’s circle foe failure for a direct shear stress test and mark the failure plane, a major principle plain and minor principal plain. 4. If the test is under a normal stress of 2.5 kg/cm2 , find the shear load at which the soil will fail.(Use ? found from...

Question