In a pipe heat exchanger, crude oil on 30 ℃ is used to cool the heavy...

In a pipe heat exchanger, crude oil on 30 ℃ is used to cool the heavy oil from 180℃ to 120℃.Mass flow of heavy oil is Wh=104kg / h，and crude oil respectively Wc=1.3×104kg/h. Specific heat, respectively is Cph=2.2 kJ/(kg•℃), Cpc=1.9 kJ/(kg•℃). Overall heat transfer coefficient K=120W/(m2•K). Try to calculate the required heat transfer area for parallel flow and countercurrent flow.

Expert Solution

Amanda K answered 2 years ago

A double pipe heat exchanger is to be designed to cool 5 gal/min of hot oil...

A double pipe heat exchanger is to be designed to cool 5 gal/min of hot oil from 250°F to 120°F using 10 gal/min of cooling water available at 70°F. The heat exchanger is to consist of sections of 0.75 inch 16 BWG copper tubing inside 1.5 inch 16 BWG tubing; the water flows in the annular space. The shell-side heat transfer coefficient for this system is known to be 737 Btu/hr×ft2×°F. a) Estimate the required length of the countercurrent exchanger,...

A counterflow, concentric tube heat exchanger is used to cool the lubricating oil for a large...

A counterflow, concentric tube heat exchanger is used to cool the lubricating oil for a large industrial gas turbine engine. The flow rate of cooling water through the inner tube (Di = 25 mm) is 0.2 kg/s, while the flow rate of oil through the outer annulus (Do = 45 mm) is 0.1 kg/s. The oil and water enter at temperatures of 100 and 30 C, respectively. How long must the tube be made if the outlet temperature of the...

Water is used to cool ethylene glycol in a 18.3-m-long double pipe heat exchanger made of...

Water is used to cool ethylene glycol in a 18.3-m-long double pipe heat exchanger made of 4-std and 2-std (both type M) copper tubing. The water inlet temperature is 15.6°C and the ethylene glycol inlet temperature is 82.2°C. The flow rate of the ethylene glycol is 9.07 kg/s, while that for the water is 13.6 kg/s. Calculate the expected outlet temperature of the ethylene glycol and determine the pressure drop expected for both streams. Assume counterflow, and place the ethylene...

A double-pipe heat exchanger is designed as an engine oil cooler. The flow rate of oil...

A double-pipe heat exchanger is designed as an engine oil cooler. The flow rate of oil is 5 kg/s, and it will be cooled from 60°C to 40°C through annulus (ID = 0.10226 m, OD = 0.1143 m). Sea water flows through the tubes (ID = 0.02664 m, OD = 0.03340 m) and is heated from 10°C to 30°C. The number of bare tubes in the annulus is 3, and the length of the hairpin is 3 m. Assume that...

Design of Shell and Tube Heat Exchanger Crude oil at 198°C is to be cooled to...

Design of Shell and Tube Heat Exchanger Crude oil at 198°C is to be cooled to 39°C. The oil flow-rate is 6.127 kg/s. Cooling water is available at 29°C and at the rate of 27.127 kg/s. The pressure drop allowance for each stream is 100 kN/m2 . Design a suitable shell and tube heat exchanger for this duty. The following are the properties of the two streams at the average temperature: water crude oil density kg/m3 990 850 viscosity mNm-2...

HEAT TRANSFER: HEAT EXCHANGER Oil flows in a heat exchanger with a mass flow rate of...

HEAT TRANSFER: HEAT EXCHANGER Oil flows in a heat exchanger with a mass flow rate of 20 kg/s and is to be cooled from 175 to 65°C with water as a coolant flowing at a rate of 30 kg/s and an inlet temperature of 12°C. The overall heat transfer coefficient is U = 1250 W/m2⋅K. a) Sketch the temperature profile and calculate the mean temperature for parallel flow, counter flow, and cross flow heat exchangers.. b) Determine the area required...

A shell-and-tube heat exchanger is to used to heat water (in the tube side) from 30...

A shell-and-tube heat exchanger is to used to heat water (in the tube side) from 30 deg C to 40 deg C at a mass flow rate of 4 kg/s. The fluid used for heating (shell side) is water entering at 90 deg C with a mass flow rate of 2 kg/s. A 1-2 STHE is used and the overall heat transfer coefficient based on the inside area is 1390 W/m2-K. The tubes are 1.875 in diameter (inside) and require...

A double-pipe heat exchanger is used to condense steam at 40°C saturation temperature. Water at an...

A double-pipe heat exchanger is used to condense steam at 40°C saturation temperature. Water at an average bulk temperature of 20°C flows at 2 m/s through the inner tube (copper, 2.54 cm ID, 3.05 cm OD). Steam at its saturation temperature flows in the annulus formed between the outer surface of the inner tube and outer tube of 6 cm ID. The average heat transfer coefficient of the condensing steam is 6,000 W/m2 ? K, and the thermal resistance of...

Cold water inside / outside diameter in the same axis two pipe heat exchanger used as...

Cold water inside / outside diameter in the same axis two pipe heat exchanger used as engine oil cooler It enters the 25/30 mm steel pipe at a temperature of 15 degrees at a speed of 0.5 m / s, Take off at a temperature of 25 degrees.Hot oil, on the inside / outside diameter of 40/46 mm steel pipe, at a temperature of 60 degrees with a speed of 0.25 m / s. enters.it is desired to cool the...

liquid oil is used in the tube side of a shell-and-tube heat exchanger with two shell...

liquid oil is used in the tube side of a shell-and-tube heat exchanger with two shell passes and four tube passes. water is heated in the shell side from 10°C to 50°C while the oil is cooled from 90°C to 60°C. the overall heat transfer coefficient is 53 W/m^2*K. the specific heat of the oil is 2.0 kJ/kg*K. Using the NTU - effectiveness method, calculate the area of the heat exchanger for a total energy transfer of 500 kW. what...

Question