Cold water inside / outside diameter in the same axis two pipe heat exchanger used as...

Cold water inside / outside diameter in the same axis two pipe heat exchanger used as engine oil cooler
It enters the 25/30 mm steel pipe at a temperature of 15 degrees at a speed of 0.5 m / s, Take off at a temperature of 25 degrees.Hot oil, on the inside / outside diameter of 40/46 mm steel pipe, at a temperature of 60 degrees with a speed of 0.25 m / s.
enters.it is desired to cool the oil 5 degrees, according to this :
A)Find pipe length for parallel flow?
B)Find the pipe length for reverse flow. Examine the results
C) Calculate the pressure loss of the oil and the required pump power in reverse flow.

Expert Solution

samet mamat answered 2 years ago

In the two-tube heat exchanger with the same axis used as engine oil cooler, cold water...

In the two-tube heat exchanger with the same axis used as engine oil cooler, cold water enters the steel pipe with inner/outer diameter of 25/30 mm (K= 55 W/mK) entering with at 15°C temperature, 0.5 m/s speed and comes out at 25°C temperature. Hot oil enters the steel pipe with inner/outer diameter of 40/46 mm with a speed of 0.25 m/s at 60°C temperature. According to the oil is required to be cooled at 5°C; A) Find the pipe length...

A double-pipe heat exchanger is used to condense steam at 40°C saturation temperature. Water at an...

A double-pipe heat exchanger is used to condense steam at 40°C saturation temperature. Water at an average bulk temperature of 20°C flows at 2 m/s through the inner tube (copper, 2.54 cm ID, 3.05 cm OD). Steam at its saturation temperature flows in the annulus formed between the outer surface of the inner tube and outer tube of 6 cm ID. The average heat transfer coefficient of the condensing steam is 6,000 W/m2 ? K, and the thermal resistance of...

Water is used to cool ethylene glycol in a 18.3-m-long double pipe heat exchanger made of...

Water is used to cool ethylene glycol in a 18.3-m-long double pipe heat exchanger made of 4-std and 2-std (both type M) copper tubing. The water inlet temperature is 15.6°C and the ethylene glycol inlet temperature is 82.2°C. The flow rate of the ethylene glycol is 9.07 kg/s, while that for the water is 13.6 kg/s. Calculate the expected outlet temperature of the ethylene glycol and determine the pressure drop expected for both streams. Assume counterflow, and place the ethylene...

A counter-flow double-pipe heat exchanger is to heat water from 20ºC to 80ºC at a rate...

A counter-flow double-pipe heat exchanger is to heat water from 20ºC to 80ºC at a rate of 1.2 kg/s. The heating is to be accomplished by geothermal water available at 160ºC at a mass flow rate of 2 kg/s. The inner tube is thin-walled, and has a diameter of 1.5 cm. If the overall heat transfer coefficient of the heat exchanger is 640 W/(m2.ºC), determine the length of the heat exchanger required to achieve the desired heating using the effectiveness-NTU...

In a pipe heat exchanger, crude oil on 30 ℃ is used to cool the heavy...

In a pipe heat exchanger, crude oil on 30 ℃ is used to cool the heavy oil from 180℃ to 120℃.Mass flow of heavy oil is Wh=104kg / h，and crude oil respectively Wc=1.3×104kg/h. Specific heat, respectively is Cph=2.2 kJ/(kg•℃), Cpc=1.9 kJ/(kg•℃). Overall heat transfer coefficient K=120W/(m2•K). Try to calculate the required heat transfer area for parallel flow and countercurrent flow.

a- Water enters a house through a pipe with inside diameter of 3.0 cm at an...

a- Water enters a house through a pipe with inside diameter of 3.0 cm at an absolute pressure of 5.0 X 105 Pa. A 1.5 cm diameter pipe leads to the second-floor bathroom 6.0 m above. When the flow speed at the inlet pipe is 2.0 m/s find: - Flow speed (velocity) of the water in the bathroom - Pressure water in the bathroom? - Calculate the volume flow rate in the bathroom.

A heat exchanger with 1 body - 4 pipe passages and 109 pipes (2.6 cm diameter...

A heat exchanger with 1 body - 4 pipe passages and 109 pipes (2.6 cm diameter each, 4 m long thin wall per passage) at each passage will be used to heat the air. The water enters the pipes with a mass flow of 8 kg / h at 350 K temperature and the air enters the body with a mass flow of 18 kg / h at a temperature of 15 C. The pollution factor of the sediment formed...

A heat exchanger with one body and eight pipe passes is designed. Water flows from the...

A heat exchanger with one body and eight pipe passes is designed. Water flows from the exhaust gas pipes as cold fluid by the body as cold fluid. Exhaust gas to the system at 210 ° C and entering at a temperature of 140 ° C The heat transfer coefficient is 392 W / m2K. On the other hand, water enters 16 iron (k = 38 W / mK) pipes with an inner diameter and outer diameter of 32 mm...

A shell-and-tube heat exchanger is to used to heat water (in the tube side) from 30...

A shell-and-tube heat exchanger is to used to heat water (in the tube side) from 30 deg C to 40 deg C at a mass flow rate of 4 kg/s. The fluid used for heating (shell side) is water entering at 90 deg C with a mass flow rate of 2 kg/s. A 1-2 STHE is used and the overall heat transfer coefficient based on the inside area is 1390 W/m2-K. The tubes are 1.875 in diameter (inside) and require...

A 30 m long pipe with an outside diameter of 75 mm is used to deliver...

A 30 m long pipe with an outside diameter of 75 mm is used to deliver steam at a rate of 2000 kg / hour. The vapor pressure is 198.53 kPa entering the pipe with a quality of 98%. The pipe needs to be given insulation with thermal conductivity of 0.2 W / (m K) so that the vapor quality only slightly decreases to 95%. The outer surface temperature of the insulation is assumed to be 25 ° C. Ignore...

Question