Air flows through a 8-in-diameter, 60-ft-long adiabatic duct with inlet conditions of V1= 550 ft/s, T01=...

Air flows through a 8-in-diameter, 60-ft-long adiabatic duct with inlet conditions of V1= 550 ft/s, T01= 650 R, and P1= 50 psia. For an average friction factor of 0.03, determine the velocity, temperature, and pressure at the exit of the duct. Please DO NOT merely copy other expert's work. I would like original work.

Expert Solution

samet mamat answered 2 years ago

Air flows through a 0.25-m-diameter duct. At the inlet the velocity is 300 m/s, and the...

Air flows through a 0.25-m-diameter duct. At the inlet the velocity is 300 m/s, and the stagnation temperature is 90°C. If the Mach number at the exit is 0.3, determine the direction and the rate of heat transfer. For the same conditions at the inlet, determine the amount of heat that must be transferred to the system if the flow is to be sonic at the exit of the duct.

Steam flows steadily through an adiabatic turbine. The inlet conditions of the steam are 4 MPa,...

Steam flows steadily through an adiabatic turbine. The inlet conditions of the steam are 4 MPa, 500°C and 80 m/s, and the exit conditions are 30 kPa, 92% quality and 50 m/s. The mass flowrate of the steam is 12 kg/s. Investigate the effect of the turbine exit pressure on the power output of the turbine. Let the exit pressure vary from 10 to 200 kPa. Plot (1) T2 vs P2 and 2) Plot the power output (W_dot_T in MW)...

Air flows in a pipe with a diameter, D=50 mm. The inlet conditions are: M1 =...

Air flows in a pipe with a diameter, D=50 mm. The inlet conditions are: M1 = 3; total pressure, P01 = 1000 kPa absolute; and temperature, T1 = 550 K. The friction coefficient is, f = 0.004. The exit Mach number decreases with the length of the pipe. Plot the following while the exit Mach number to be changed from 2.5 to 0.99 with decrements of ?M=0.01: a) L, length of the pipe that is going to give the desired...

Consider a pipe (diameter of 50 mm) with air flowing through it. The inlet conditions are:...

Consider a pipe (diameter of 50 mm) with air flowing through it. The inlet conditions are: Mach 3; total pressure = 1000 kPa and 550 K. The friction coefficient (f) is 0.004. The exit Mach number decreases with the length of the pipe. Assume adiabatic, steady flow. Write a short Matlab code and plot the following, while the exit Mach number changes from 2.5 to 0.99 with increments of ?M=0.01. Find the length of the pipe that is going to...

Air flows down a pipe with a diameter of 0.15 m. At the inlet to the...

Air flows down a pipe with a diameter of 0.15 m. At the inlet to the pipe, the Mach number is 0.1, the pressure is 70 kPa, and the temperature is 35°C. If the flow can be assumed to be adiabatic and if the mean friction factor is 0.005, determine the length of the pipe if the Mach number at the exit is 0.6. Also, find the pressure and temperature at the exit to the pipe.

Air flows through a constant area duct. The pressure and temperature of the air at the...

Air flows through a constant area duct. The pressure and temperature of the air at the inlet to the duct are P1 = 100 kPa absolute, and T1 = 298 K, respectively. Inlet Mach number is M1 = 0.1. Heat is transferred to the air as it flows through the duct and as a result the Mach number at the exit increases. Write a Matlab code and plot the following: a) Find the pressure and temperature at the exit, while...

An adiabatic air compressor with inlet conditions of 100 kPa, 27 C and an exit pressure...

An adiabatic air compressor with inlet conditions of 100 kPa, 27 C and an exit pressure of 500 kPa has an inlet volume flow rate of 5 m3/s and operates in steady flow. Calculate the minimum power required to drive the compressor.

Hot air flows with a mass flow rate of 0.05 kg/s through an insulated square duct...

Hot air flows with a mass flow rate of 0.05 kg/s through an insulated square duct with side of 0.15m, the hot air enters at 103 oC and after a distance of 5m, cools to 85 oC. The heat transfer coefficient between the duct outer surface and the ambient air (Tair = 0 oC) is 6 W/m2 K. Calculate the heat transfer coefficient between hot air and duct inner wall. Air Cp = 1.011 KJ/kg K; air k = 0.0306...

Water flows through a 3 inch diameter pipe at a velocity of 10 ft/s. Find the...

Water flows through a 3 inch diameter pipe at a velocity of 10 ft/s. Find the a) volume flow rate in cfs(cubic feet per second) and gpm(gallons per minute) b) mass flow rate in slug/second.

Air flows through a nozzle which has inlet areas of (10 cm2 ). If the air...

Air flows through a nozzle which has inlet areas of (10 cm2 ). If the air has a velocity of (120 m/s) a temperature (300K) and a pressure of (700kpa) at the inlet section and a pressure of (250kpa) at the exit, find the mass flow rate through the nozzle and the velocity at the exit of the nozzle, assuming one- dimensional isentropic flow. (R=287 J/kg. K), (K=1.4). (25%)

Question