Steam flows steadily through an adiabatic turbine. The inlet conditions of the steam are 4 MPa,...

Steam flows steadily through an adiabatic turbine. The inlet conditions of the steam are 4
MPa, 500°C and 80 m/s, and the exit conditions are 30 kPa, 92% quality and 50 m/s. The
mass flowrate of the steam is 12 kg/s. Investigate the effect of the turbine exit pressure on
the power output of the turbine. Let the exit pressure vary from 10 to 200 kPa. Plot (1) T2
vs P2 and 2) Plot the power output (W_dot_T in MW) against the exit pressure (P2 in kPa)
and discuss the results.

Expert Solution

samet mamat answered 2 years ago

A steam turbine operates with steam at inlet conditions of 3.5 MPa and 3500 C. The...

A steam turbine operates with steam at inlet conditions of 3.5 MPa and 3500 C. The exit stream leave the turbine is at 0.8 MPa and is known to contain a mixture of saturated vapor and liquid. The steam rate through the turbine is 1000 kg/h. A (negligible) fraction of exit stream is bled through a throttle valve to 0.10 MPa and is found to be 1250 C. The measured output of the turbine is 100 kW. a) Determine the...

Steam at 400°C and 40 bar flows steadily through an adiabatic turbine at a volumetric flowrate...

Steam at 400°C and 40 bar flows steadily through an adiabatic turbine at a volumetric flowrate of 5,000 m3/h. The steam leaving the turbine at 1 bar is then cooled at constant pressure in a condenser to 25°C. The rate of transfer from the condenser is 50 MW. Calculate the power output generated by the turbine (MW). Clearly state assumptions (if any) and reference state.

Steam enters an adiabatic turbine steadily at 3 MPa and 400°C and leaves at 50 kPa....

Steam enters an adiabatic turbine steadily at 3 MPa and 400°C and leaves at 50 kPa. If the isentropic efficiency of the turbine is 66.7%, determine the actual temperature of steam at turbine exit. The mass flow rate of the steam flowing through the turbine is 218 kg/min, determine the power output from the turbine. Plot the T-s diagram.

Steam at 4 MPa and 350°C is expanded in an adiabatic turbine to 120 kPa. What...

Steam at 4 MPa and 350°C is expanded in an adiabatic turbine to 120 kPa. What is the isentropic efficiency of this turbine if the steam is exhausted as a saturated vapor?

4. A steam turbine has an inlet flow of 3 kg/s at 3.5 MPa and 450...

4. A steam turbine has an inlet flow of 3 kg/s at 3.5 MPa and 450 C with a velocity of 140 m/s. the exit of the turbine is 800 kPa and 300 C at a very low velocity. Calculate a.) the work produced in (MW) by the turbine, and b.) The entropy generated in (kW/k)

An adiabatic steam turbine receives 50 kg/s of superheated steam at 5 MPa and 500oC. Steam...

An adiabatic steam turbine receives 50 kg/s of superheated steam at 5 MPa and 500oC. Steam exits the turbine with a pressure of 100 kPa. Determine the minimum exit quality and the maximum power output of the turbine in kW.

Steam expands in a thermally isolated turbine steadily. The inlet pressure is 1MPa and temperature is...

Steam expands in a thermally isolated turbine steadily. The inlet pressure is 1MPa and temperature is 800 C, and the exit state is 300 kPA and 150 C. a- Determine the power generated by the turbine per unit mass flow rate of steam. b- Evaluate the entropy generation rate per unit mass flow rate of steam and drive a conclusion whether the turbine operates reversibly, irreversibly or the operation is impossible.

Steam enters a turbine at a velocity of 200 m/s. The inlet conditions of the steam...

Steam enters a turbine at a velocity of 200 m/s. The inlet conditions of the steam are at 4000 kPA and 500°C. The diameter of the inlet pipe is 50 mm. The outlet conditions of the steam are 80 kPa and a quality of 1.0. The diameter of the outlet pipe is 250 mm. Determine the turbine power output in kJ/s assuming the kinetic energy change and potential energy change are both negligible. Calculate the change in kinetic energy to...

a steam turbine has an inlet flow of 3 kg/s water at 3.5 MPa and 450°C...

a steam turbine has an inlet flow of 3 kg/s water at 3.5 MPa and 450°C with a velocity of 140 m/s. The exit is at 800 KPa and 300°C and very low velocity. (a) How much heat (in MW) is assumed to be transferred into the turbine? (b) what is the work that goes into the turbine? (c) find the work produced by the turbine? (d) Find the entropy generation of the process. (e) find the carnot efficiency of...

Steam enters an adiabatic turbine at 500C and 4.0MPa and 80m/s. The steam leaves the turbine...

Steam enters an adiabatic turbine at 500C and 4.0MPa and 80m/s. The steam leaves the turbine as saturated liquid-vapor mixture at 30kPa, quality of 92% and 50m/s. The mass flow rate of steam through the turbine is 12kg/s. (10 pts) Determine change in kinetic energy (10 pts) Determine the rate of work (power) done by the steam in the turbine, in kW (neglect potential energy change). (10 pts) Determine the flow area at the entrance to the turbine, in m2....

Question