Question

In: Mechanical Engineering

A cylindrical specimen of aluminum having a diameter of 0.75 inches and a length of 8...

A cylindrical specimen of aluminum having a diameter of 0.75 inches and a length of 8 inches is deformed elastically in tension with a force of 11,000 lb. Assume the following properties: Modulus of Elasticity: 10 Mpsi; Yield Strength: 40 kpsi; Tensile Strenght: 50 kpsi; Percent Elongation: 17; Poisson's Ratio: .33 Determine the following: (a) The amount by which this specimen will elongate in the direction of the applied stress (b) The change in diameter of the specimen. Will the diameter increase or decrease?

Solutions

Expert Solution


Related Solutions

A cylindrical specimen of some metal alloy 8.6 mm in diameter is stressed in tension. A...
A cylindrical specimen of some metal alloy 8.6 mm in diameter is stressed in tension. A force of 9070 N produces an elastic reduction in specimen diameter of 0.0048 mm. Calculate the elastic modulus (in GPa) of this material if its Poisson's ratio is 0.33.
A birthday candle is 2.5 inches long and 0.75 cm in diameter. It’s made of paraffin...
A birthday candle is 2.5 inches long and 0.75 cm in diameter. It’s made of paraffin wax, which is a mixture of various hydrocarbons, but for the sake of argument we’ll assume it’s all C31H64, since that’s the major component. Its density is 0.90 g/cm3 paraffin. If air is 20.95% O2 by volume, and the density of O2 is 1.43 g/L, then how many liters of air will the candle consume if it completely burns up? (Note that paraffin combines...
A soil sample weighing 122g has diameter and length equal to 4.5 inches and 11 inches,...
A soil sample weighing 122g has diameter and length equal to 4.5 inches and 11 inches, respectively. The moisture content in soil came out to be 40 %. If specific gravity of soil solids is 2.67. Find Bulk unit weight, dry mass of sample, voids ratio, porosity, dry unit weight and degree of saturation of soil sample.
A short and hollow cylindrical bar, having an outer diameter of 4.00 in and an inner...
A short and hollow cylindrical bar, having an outer diameter of 4.00 in and an inner diameter of 7 in, is subjected to two simultaneous loads - an axial compressive force of 75,100 lb. and a torsional moment of 20,100 lb • in. You are required to create two-dimensional (2D) and three-dimensional (3D) stress elements for two stress states on the outer and inner surfaces of the bar to in-plane and out-of-plane stresses, respectively and then draw the 2D and...
Problem 7.56 A three-point bending test was performed on an aluminum oxide specimen having a circular...
Problem 7.56 A three-point bending test was performed on an aluminum oxide specimen having a circular cross section of radius 4.7 mm; the specimen fractured at a load of 3740 N when the distance between support points was 44 mm. Another test is to be performed on a specimen of this same material, but one that has a square cross section of 11 mm in length on each edge. At what load would you expect this specimen to fracture if...
A cylindrical shaped potato with length 2 cm and a diameter of 0.5 cm was dried...
A cylindrical shaped potato with length 2 cm and a diameter of 0.5 cm was dried at a temperature of 65 o C in a convective oven for 24 h, if the surface temperature of the potato remained at 62 o C throughout the drying operation, describe the different changes that occurs during the constant and falling rate periods
Question 1 a) A cylindrical feedstock of length = 35.4 cm and diameter = 10 cm...
Question 1 a) A cylindrical feedstock of length = 35.4 cm and diameter = 10 cm is subjected to turning using a high speed steel tool. For this tool, n and C values in the Taylor tool life equation are 0.125 and 70 m/min, respectively. The cost for hiring an operator and using the machine tool are $82 per hour. The tooling cost per edge of cutting is $5. Loading and unloading the part on to the machine takes about...
A pure aluminum bar has a diameter of 15 cm and a length of 1.25 m....
A pure aluminum bar has a diameter of 15 cm and a length of 1.25 m. The rod is initially uniform in temperature at 300?C. The bar is now suddenly exposed to a convection environment at 50?C with h = 1250 W/m K. How long does it take the center to cool to a temperature of 80?C? (a) Determine if a lumped capacitance analysis is or is not appropriate. (b) Determine the cooling time assuming the lumped capacitance model is...
A cylindrical pressure vessel with flat ends of length 6 ft and inner diameter of 35...
A cylindrical pressure vessel with flat ends of length 6 ft and inner diameter of 35 in. is subjected to an internal gauge pressure of 150 psi. Neglect the end effects and the mass of ends of the pressure vessel in your design. Take the factor of safety as 1.95: 1. Design the radial thickness of the pressure vessel using steel. For steel, assume that the Young’s modulus is 30 Msi, Poisson’s ratio is 0.3, specific gravity of steel is...
A spherical particle having a diameter of 9.3 x 10-3 inches and a specific gravity of...
A spherical particle having a diameter of 9.3 x 10-3 inches and a specific gravity of 1.85 is placed on a horizontal screen. Air is blown through the screen vertically at a temperature of 20 oC and a pressure of l atm. Calculate the following: (a) Velocity required to just lift the particle. (b) Particle Reynolds number at the condition of part (a). (c) Drag force. (d) Drag coefficient CD. Given; Viscosity of air = 1.23 x I0 -5 lbm/ft.s...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT