Question

In: Mechanical Engineering

Problem 7.56 A three-point bending test was performed on an aluminum oxide specimen having a circular...

Problem 7.56

A three-point bending test was performed on an aluminum oxide specimen having a circular cross section of radius 4.7 mm; the specimen fractured at a load of 3740 N when the distance between support points was 44 mm. Another test is to be performed on a specimen of this same material, but one that has a square cross section of 11 mm in length on each edge. At what load would you expect this specimen to fracture if the support point separation is maintained at 44 mm?

Solutions

Expert Solution


Related Solutions

A cylindrical specimen of aluminum having a diameter of 0.75 inches and a length of 8...
A cylindrical specimen of aluminum having a diameter of 0.75 inches and a length of 8 inches is deformed elastically in tension with a force of 11,000 lb. Assume the following properties: Modulus of Elasticity: 10 Mpsi; Yield Strength: 40 kpsi; Tensile Strenght: 50 kpsi; Percent Elongation: 17; Poisson's Ratio: .33 Determine the following: (a) The amount by which this specimen will elongate in the direction of the applied stress (b) The change in diameter of the specimen. Will the...
A torsion test is performed on an aluminum probe, with the following results given in the...
A torsion test is performed on an aluminum probe, with the following results given in the following table: (degress(º)) 0 5 10 15 20 25 30 35 40 45 50 55 60 80 T kgf.m 0 5 11 14 14.5 14.7 16.3 16.4 16.5 16.6 16.7 16.4 16.5 16 The probe dimensions are as follows: Length(L) Diameter(D) 180 10 Through your graph of behavior of shear to torsion against angular deformation determine the following: • Limit proportional to the cut...
4. The following data were obtained from a creep test for a specimen having an initial...
4. The following data were obtained from a creep test for a specimen having an initial gage length of 2.0 in. and an initial diameter of 0.6 in. The initial stress applied to the material is 10,000 psi. The diameter of the specimen after fracture is 0.52 in. Length Between Gage Marks ( (in.) Time (h) Strain (in./in.) 2.004 0 0.002 2.01 100 0.004 2.02 200 0.006 2.03 400 0.008 2.045 1000 0.012 2.075 2000 0.020 2.135 4000 0.035 2.193...
These are the results of a three point test cross in Drosophila for the three loci...
These are the results of a three point test cross in Drosophila for the three loci cv f v: cv + + = 155, cv f + = 78, + f + = 145, cv f v = 274, cv + v = 192, + + v = 72, + f v = 144, + + + = 230. What is the map distance to 2 decimal places between the v and f loci? Hint: Establish gene order first."
"These are the results of a three point test cross in Drosophila for the three loci...
"These are the results of a three point test cross in Drosophila for the three loci cv f v: cv + + = 212, + v + = 48, + + + = 606, cv v + = 771, cv f v = 299, cv + f = 52, + f v = 229, + + f = 850. What is the map distance to 2 decimal places between the cv and f loci? Hint: Establish gene order first."
I am having difficulty with this problem. My break-even point in dollar sales totals appears to...
I am having difficulty with this problem. My break-even point in dollar sales totals appears to be off by several hundred dollars.   Pittman Company is a small but growing manufacturer of telecommunications equipment. The company has no sales force of its own; rather, it relies completely on independent sales agents to market its products. These agents are paid a sales commission of 14% for all items sold. Barbara Cheney, Pittman’s controller, has just prepared the company’s budgeted income statement for...
You are performing a three-point test cross in order to map the order and distance between...
You are performing a three-point test cross in order to map the order and distance between three genes, designated X, Y, and Z, and you obtain the following results: Phenotypes      Number Observed + Y +                          1 + + Z                          72 X + Z                           2 X Y +                           70 X + +                          3 + Y Z                         2 X Y Z                           0 + + +                          0 Which gene is in the middle? a) X b) Y c) Z d)...
In a three-point balancing test without phase the values for the original vibrations are V0=10 mm,...
In a three-point balancing test without phase the values for the original vibrations are V0=10 mm, and the values of the amplitude of vibration for the three points in the test with a trial mass, mt, of 50 g are: V1=14 mm at 0 degrees V2=20 mm at 120 degrees V3=7 mm at 240 degrees Apply the mathematical method,
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT