Question

In: Mechanical Engineering

A compression spring has a diameter of 0.67 in and a coil diameter of 0.067 in,...

A compression spring has a diameter of 0.67 in and a coil diameter of 0.067 in, with 30 total coils.
The spring is to be made of unpeened HD A227 wire and have squared and ground ends. Find the
fatigue factor of safety when repeatedly cycled from 0 to 10.3 lbf. Use the Gerber fatigue criterion
and the Zimmerli data.

Solutions

Expert Solution


Related Solutions

A helical compression spring is wound using 1 mm-diameter music wire. The outside coil diameter of...
A helical compression spring is wound using 1 mm-diameter music wire. The outside coil diameter of the spring is 11 mm. The ends are squared and there are 12 total turns. (a) Estimate the torsional yield strength of the wire. (b) Estimate the static load corresponding to the yield strength. (c) Estimate the scale of the spring. (d) Estimate the solid length of the spring. (e) Is there any possibility for buckling?
Starting with a spring index of C = 10, design a compression coil spring of 302...
Starting with a spring index of C = 10, design a compression coil spring of 302 stainless wire with squared ends. The spring is to deflect y = 50 mm, for an applied force of F = 90 N and to close solid when ys = 60 mm. At closure, use a design factor of 1.2 guarding against yielding. Select the smallest diameter wire where wire diameters are available in 0.2-mm increments between 0.2 to 3.2 mm. For the design,...
An as-wound helical-coil compression spring with infinite fatigue life is needed to resist a dynamic load...
An as-wound helical-coil compression spring with infinite fatigue life is needed to resist a dynamic load that varies from 8.0 to 24.0 lbf at 45.0 Hz over a dynamic deflection of 0.3 in. Because of assembly considerations, the solid length of the spring cannot be more than 1.2 in. The spring should have squared and ground ends and is to be made from peened music wire. Upon closure, use a design factor of 1.2 guarding against yielding and a fractional...
Problem 10-3 A helical compression spring is wound using 2.5- mm -diameter music wire. The spring...
Problem 10-3 A helical compression spring is wound using 2.5- mm -diameter music wire. The spring has an outside diameter of 31 mm with plain ground ends, and 14 total coils. (a) Estimate the spring rate. (b) What force is needed to compress this spring to closure? (c) What should the free length be to ensure that when the spring is compressed solid the torsional stress does not exceed the yield strength? (d) Is there a possibility that the spring...
10-35: A helical coil compression spring is needed for food service machinery. The load varies from...
10-35: A helical coil compression spring is needed for food service machinery. The load varies from a minimum of 4 lbf to a maximum of 18 lbf. The spring rate k is to be 9.5 lbf/in. The outside diameter of the spring cannot exceed . The springmaker has available suitable dies for drawing 0.080-, 0.0915-, 0.1055-, and 0.1205-in-diameter wire. Use squared and ground ends, and an unpeened material. Using a fatigue design factor nf of 1.5, and the Gerber-Zimmerli fatigue-failure...
A 40-turn coil has a diameter of 11 cm. The coil is placed in a spatially...
A 40-turn coil has a diameter of 11 cm. The coil is placed in a spatially uniform magnetic field of magnitude 0.40 T so that the face of the coil and the magnetic field are perpendicular. Find the magnitude of the emf induced in the coil (in V) if the magnetic field is reduced to zero uniformly in the following times. (a) 0.30 s V (b) 3.0 s V (c) 65 s V
5 of industrial examples :(with photo) -compression spring
5 of industrial examples :(with photo) -compression spring
6-Torque on a coil. A circular loop of wire has a diameter of 20.0 cm and...
6-Torque on a coil. A circular loop of wire has a diameter of 20.0 cm and contains 10 loops. The current in each loop is 3.00 A, and the coil is placed in a 2.00-T external magnetic field. Determine the maximum and minimum torque exerted on the coil by the field.
A helical compression spring has 14 active coils and the free length is 12.5in. The outside...
A helical compression spring has 14 active coils and the free length is 12.5in. The outside diameter is 7/16 in and the spring has squared and ground ends. The end plates are constrained to be parallel. The material is music wire with presetting. The wire diameter is 0.042 in. Determine: (1) for static conditions compute the spring index, the solid length, the stress when the spring is compressed to the solid length. Check if static yielding occurs while the spring...
A 26-turn circular coil has a diameter of 0.60 m. It is placed with its axis...
A 26-turn circular coil has a diameter of 0.60 m. It is placed with its axis along the direction of a 50.0-?T magnetic field and then flipped through an angle of 180° in 0.170 s. Determine the average emf generated in the coil, and the magnitude of the emf at 0.085 s. [4.3 x 10-3 V, 6.8 x 10-3 V] (Note: Very few students got the second part correct, you need to find the function for emf with respect to...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT