1. Evaluate a music wire spring with plain ends where the wire diameter is 0.100” and...

1. Evaluate a music wire spring with plain ends where the wire diameter is 0.100” and the outer
diameter is 0.600”. The desired spring rate is 100 lbf/in and the free length is 2.4”. Let the load
safety factor be 1.00.
a) What is the spring index, C?
b) What is the total number of coils, Nt?
c) What is solid length, Ls?
d) What is the maximum suggested load?
e) What is the maximum suggested deflection?
f) What is the force to close to solid, Fs?
g) What is the critical length?
h) What is the critical frequency?
i) What is the factor of safety, solid, ns?

Expert Solution

Give a thumbs up if my work clarified your doubt....

samet mamat answered 8 months ago

A helical compression spring is wound using 1 mm-diameter music wire. The outside coil diameter of...

A helical compression spring is wound using 1 mm-diameter music wire. The outside coil diameter of the spring is 11 mm. The ends are squared and there are 12 total turns. (a) Estimate the torsional yield strength of the wire. (b) Estimate the static load corresponding to the yield strength. (c) Estimate the scale of the spring. (d) Estimate the solid length of the spring. (e) Is there any possibility for buckling?

Problem 10-3 A helical compression spring is wound using 2.5- mm -diameter music wire. The spring...

Problem 10-3 A helical compression spring is wound using 2.5- mm -diameter music wire. The spring has an outside diameter of 31 mm with plain ground ends, and 14 total coils. (a) Estimate the spring rate. (b) What force is needed to compress this spring to closure? (c) What should the free length be to ensure that when the spring is compressed solid the torsional stress does not exceed the yield strength? (d) Is there a possibility that the spring...

3. Use oil-tempered 0.060” diameter wire to make a spring with squared and closed ends, a...

3. Use oil-tempered 0.060” diameter wire to make a spring with squared and closed ends, a spring index of 4, and solid length of 1.25”. Use a load factor of safety of 1.05 and make the free length 1.75 inches. e) What is the force to close to solid, Fs? f) What is the critical frequency? g) What is the factor of safety, solid, ns?

A 1.50-m-long wire having a mass of 0.100 kg is fixed at both ends. The tension...

A 1.50-m-long wire having a mass of 0.100 kg is fixed at both ends. The tension in the wire is maintained at 25.0 N. (a) What are the frequencies of the first three allowed modes of vibration? f1 = 6.4549 Hz f2 = 12.9099 Hz f3 = 19.3649 Hz (b) If a node is observed at a point 0.300 m from one end, in what mode and with what frequency is it vibrating? (Select all that apply.) The frequency is...

If the wire diameter decreases to 1 mm but the length is still 20 m and...

If the wire diameter decreases to 1 mm but the length is still 20 m and still carrying the same 20.0 A current, the drift speed of electrons will (increase / decrease / stay the same), the current density will (increase / decrease / stay the same), the resistivity of the wire will (increase / decrease / stay the same), the resistance of the wire will (increase / decrease / stay the same), the electric field inside the wire will (increase / decrease / stay...

1-What is the resistance of a 5km long copper wire with a diameter of 4mm? a....

1-What is the resistance of a 5km long copper wire with a diameter of 4mm? a. 1.65 ohms b. 0.0015 ohms c. .0065 ohms d. 6.7 ohms 2- three 4mF capacitor are connected in series across a 12 V battery. The total charges stored by this compination of capacitor is A. 24 mC B. 16 mC C. 48 mC D. 144 mC E. None of the above 3. What would be the energy stored in the capacitor in the previous...

1. An aluminum circular cylinder 50 mm in diameter with ends insulated is initially at 100◦C....

1. An aluminum circular cylinder 50 mm in diameter with ends insulated is initially at 100◦C. Approximate the temperature at the center of the cylinder after 2 s if the lateral surface is kept at 0◦C.For aluminum, k = 8.6 × 10−5m2 /s. 2. A circular cylinder 1 m in radius is completely insulated and has an initial temperature distribution 100r ◦C. Find an expression for the temperature as a function of r and t. Write integral expressions for at...

Question 1: A 13.7 cm diameter loop of wire is initially oriented perpendicular to a 1.9...

Question 1: A 13.7 cm diameter loop of wire is initially oriented perpendicular to a 1.9 T magnetic field. The loop is rotated so that its plane is parallel to the field direction in 0.33 s . Part A: What is the average induced emf in the loop? Question 2: A 7.4 cm diameter circular loop of wire is in a 0.71 T magnetic field. The loop is removed from the field in 0.28 s . Assume that the loop...

1)calculate the polar moment of inertia of a wire with a 2 mm diameter 2) what...

1)calculate the polar moment of inertia of a wire with a 2 mm diameter 2) what is the difference between the elastic modulus (E) and the shear Modulus (G) ?

Suppose a 1-m length of aluminum wire 0.001 m in diameter is held in a horizontal...

Suppose a 1-m length of aluminum wire 0.001 m in diameter is held in a horizontal east-west position (in vertical equilibrium) by an external magnetic eld directed north of strength 1 G = 10-4 T. The density aluminum = 2:70 103 kg/m3 and the resistivity aluminum = 2:65 10?8 m. Also note the volume of a cylinder is Vcyl = r2h. (a) Find the resistance RAl of the aluminum wire. (b) Find the volume VAl of the aluminum wire. (c)...

Question