Question

In: Mechanical Engineering

Thrust is transmitted to an aircraft control by a tube which is 1 m long with...

Thrust is transmitted to an aircraft control by a tube which is 1 m long with an outside diameter of 25 mm and wall thickness of 2 mm. Assume the ends of the tube to be pin jointed and guided. Calculate the failing load by:

a) Euler theory

b) Rankine Theory

Assume E = 200 GN/m2, a =1/3000 and ?c = 300 MN/m2

Solutions

Expert Solution

seclect minimum among them

So failing load is 7.22 kN.

samet mamat answered 2 years ago
Next > < Previous

Related Solutions

A tube at room temperature which is 0.680 m long is open on both ends. Which...
A tube at room temperature which is 0.680 m long is open on both ends. Which frequencies of sound will resonate in the tube? The tube is then covered on one end. Which frequencies of sound will resonate in the tube now? e) lowest frequency f) 2nd lowest frequency g) 3rd lowest frequency h) What is the highest frequency of audible sound that will resonate in this tube?
An aircraft is in level flight at airspeed v(t) m/s with thrust T(t) N at cruising...
An aircraft is in level flight at airspeed v(t) m/s with thrust T(t) N at cruising altitude. Suppose that at v0 = 250 m/s, the aerodynamic drag experienced by the aircraft at this altitude is: Fd(v) = 0.25v 2 . (1) Then, an extremely simplified model relating v(t) to T(t) is: mv˙(t) + Fd(v(t)) = T(t), (2) where m = 25000 kg. Assume v(t) is always positive. Question 1. Linearize (2) at v0 = 250 m/s, and an appropriate nominal...
project question: 'Design and build a thrust measurement system for model aircraft engines ' 1- Questions...
project question: 'Design and build a thrust measurement system for model aircraft engines ' 1- Questions i) sketch ii) ideas iii) plan iv) introduction, background, theory , abstract etc...
A cylindrical tube that is 2.20 m long and has a radius of 150 mm is...
A cylindrical tube that is 2.20 m long and has a radius of 150 mm is filled with water. It is oriented with its long central axis vertical, and it is open to the air at the upper end. A hole 80.0 mm in radius is drilled in the bottom, and the water is allowed to drain out. When the water level is half the height of the tube, (a) what is the speed of the water exiting through the...
Is the thrust generated typical of a small jet aircraft engine? I got -99 N explain...
Is the thrust generated typical of a small jet aircraft engine? I got -99 N explain and give me a source
Is the thrust generated typical of a small jet aircraft engine? I got -99 N explain...
Is the thrust generated typical of a small jet aircraft engine? I got -99 N explain and give me a source
You have a column of air 1.2 m long. The hard bottom of the tube forces...
You have a column of air 1.2 m long. The hard bottom of the tube forces a node there and the open end at the top of the tube forces an antinode there. Sound waves from a 1024 Hz tuning fork are sent down the column. Compute the wavelengths and frequencies for the first three allowed harmonics within the column.
The water level in a vertical glass tube 1.00 m long can be adjusted to any...
The water level in a vertical glass tube 1.00 m long can be adjusted to any position in the tube. A tuning fork vibrating at 716 Hz is held just over the open top end of the tube, to set up a standing wave of sound in the air-filled top portion of the tube. (That air-filled top portion acts as a tube with one end closed and the other end open.) take the speed of sound to be 343 m/s....
Methane gas is diffusing in a straight tube 0.1 m long containing helium at 298 k...
Methane gas is diffusing in a straight tube 0.1 m long containing helium at 298 k and a total pressure of 1.01325 x 10^5 Pa. the partial pressure of CH4 is 1.400 x 10^4 Pa at one end and 1.333 x 10^3 at the other end. Helium is insoluble in one boundary, and hence is non diffusing or stagnant. Calculate the flux of methane in kg mol/s m^2
"An aircraft control actuator is part of the flight control system that enables an airplane to...
"An aircraft control actuator is part of the flight control system that enables an airplane to fly. It is important that the actuators are reliable. Reliability can be defined as the probability a system is functioning, so it is a number between 0 and 1. One way to increase reliability of the actuator is to increase the torque. The reliability R as a function of the maximum torque T (in Newton-meters) is given by R(T)=0.91*exp(0.027T) where torque T is between...
ADVERTISEMENT
Subjects
ADVERTISEMENT
Latest Questions
ADVERTISEMENT