Question

In: Civil Engineering

How the pavement rigid design will be affected if the modulus of elasticity of concrete increased?

How the pavement rigid design will be affected if the modulus of elasticity of concrete increased?

Solutions

Expert Solution

In case of any query please comment. If you have liked the solution then please THUMBS UP.


Related Solutions

Modulus of Elasticity of Concrete? Explain how it is defined. Modulus of Elasticity of steel?
Modulus of Elasticity of Concrete? Explain how it is defined. Modulus of Elasticity of steel?
A Portland Cement Concrete (rigid) pavement is to be designed using AASHTO empirical design method. The...
A Portland Cement Concrete (rigid) pavement is to be designed using AASHTO empirical design method. The pavement should have an 8" granular sub-base having elastic modulus (Esb) of 50x103 psi. The resilient modulus of the subgrade is 5000 psi, and lying just 5 feet above rock strata (bed rock). (a) Determine the design k value, assuming loss of support factor (LSF) of 2. (b) Use the k value obtained from (a) to determine the thickness of the rigid pavement.   Assume...
Design of Rigid pavement for new construction - USING AASHTO METHOD
Design of Rigid pavement for new construction - USING AASHTO METHOD
A new highway is to be constructed. Design A calls for a concrete pavement costing​$90 per...
A new highway is to be constructed. Design A calls for a concrete pavement costing​$90 per foot with a 20​-year​  life;four paved ditches costing ​$5 per foot​ each; and four box culverts every​ mile, each costing ​$9,000 and having a 20​-year life. Annual maintenance will cost ​$1,700 per​ mile; the culverts must be cleaned every five years at a cost of​$350 each per mile. Design B calls for a bituminous pavement costing ​$45 per foot with a 10-year ​life;four sodded ditches...
Design the concrete mix according to the following conditions: Design Environment Pavement slab, Bozeman, Montana (cold...
Design the concrete mix according to the following conditions: Design Environment Pavement slab, Bozeman, Montana (cold climate) Required design strength = 3000 psi Slab thickness = 12 in Statistical data indicate a standard deviation of compressive strength of 250 psi is expected (more than 30 samples) Only air entrainer is allowed. Available materials Air entrainer: Manufacture specification is 0.15 fl oz/1% air/100lb cement Coarse aggregate: 2in. nominal maximum size, crushed stone Bulk oven dry specific gravity = 2.573, absorption =...
Discuss how M-E PDG improved rigid pavement design process regarding the effects of climate/environmental on PCC...
Discuss how M-E PDG improved rigid pavement design process regarding the effects of climate/environmental on PCC ( portland cement concrete) material properties and structural behavior.
A concrete mix design is needed for a residential street paving project in Detroit, Michigan. Pavement...
A concrete mix design is needed for a residential street paving project in Detroit, Michigan. Pavement thickness is 8”, unreinforced, subjected to freezing and thawing and deicing agents are anticipated. The specified compressive strength is 4000 psi. Assume both Fine Aggregate (FA) and Coarse Aggregate (CA) are in saturated surface dry condition. Specific Gravity of Fine Aggregate (FA) = 2.71 Fineness Modulus (FM) of Fine Aggregate (FA) = 2.70 Specific Gravity of Coarse Aggregate (CA) = 2.65 Bulk Density of...
Pavement Design: New pavement design is to be constructed in 2026. The new average daily traffic...
Pavement Design: New pavement design is to be constructed in 2026. The new average daily traffic for commercial vehicles on the opening day will be 1700. Use: Growth rate = 6% Subgrade CBR = 3% Design life = 20 years
A concrete mix was designed for a concrete road pavement (i.e. heavy mass concrete). A 28-day...
A concrete mix was designed for a concrete road pavement (i.e. heavy mass concrete). A 28-day strength of 26 MPa is required. The exposure classification for durability purposes is C. One hundred laboratory test results on the controlling mix show a standard deviation of 5.3 MPa (k=1.65). The density of crushed coarse aggregate is 2850 kg/m3 and its dry rodded density is 1600 kg/m3 and the maximum size to be used is 10 mm. The specific gravity of fine aggregate...
A rigid pavement is to be designed to provide a service life of 20 years and...
A rigid pavement is to be designed to provide a service life of 20 years and has an initial PSI of 4.4 and a TSI of 2.5. The modulus of subgrade reaction is determined to be 300 lb/in3. For design, the daily car, pickup truck, and light van traffic is 30,000; and the daily truck traffic consists of 300 passes of single-unit trucks with single and tandem axles, and 400 passes of tractor semi-trailer trucks with single, tandem, and triple...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT