3. Design and draw a circuit using the cascade system to operate two cylinders (A and...

3. Design and draw a circuit using the cascade system to operate two cylinders (A and B) which, on the operation of a start valve, produces the sequence A – B + B – A+. The cylinders should park in the positions B – A + when the start switch is in the ‘off’ position.

4. Modify the circuit designed for question 3 to provide an emergency stop which will park both cylinders in the extended position (i.e. A + B +).

5. Modify the circuit designed for question 3 to provide a fail safe. The fail safe should:

(a) act in the event of a reduced pressure at inlet to the group selecting valve

(b) park the cylinders in the retracted position

Solutions

Expert Solution

samet mamat answered 1 year ago

Next > < Previous

Related Solutions

Identify FM Broadcasting System in wireless communication and design circuit. Draw the appropriate circuit diagram or...

Identify FM Broadcasting System in wireless communication and design circuit. Draw the appropriate circuit diagram or functioning diagram. Develop circuit diagram in MATLAB for FM Broadcasting System and run the simulation.

Draw the C.S circuit with cascade connection. Explain the features of this C.S over the simple...

Draw the C.S circuit with cascade connection. Explain the features of this C.S over the simple C.S.

Using known op amp configurations, design and draw an op amp circuit to convert Farenheit to...

Using known op amp configurations, design and draw an op amp circuit to convert Farenheit to Celcius. C=5/9(F-32)

Design on of these 3 circuits : Direction circuit ,Pressure circuit ,sequentional circuit one of these*

Implement a circuit for following scenario using NOR gate only, draw circuit using multiplexer In a...

Implement a circuit for following scenario using NOR gate only, draw circuit using multiplexer In a certain chemical – processing plant, a liquid chemical is used in a manufacturing process. The chemical is stored in three different tanks. A level sensor in each tank produces a HIGH voltage when the level of the chemical in the tank drops below a specified point. Design a circuit that monitors the chemical level and indicates when the level in any two of the...

design and draw the circuit of RL HPF, find the required value of the inductor to...

design and draw the circuit of RL HPF, find the required value of the inductor to get critical Frequency F,r=20KHz, assume the resistor R=(100ohms) and the input Vrms=10V MULTISIM

Design and implement a sequential circuit that counts from 0-3 in a repeating cycle with two...

Design and implement a sequential circuit that counts from 0-3 in a repeating cycle with two inputs: step and reset. If the step input is 1 the count progresses to the next value, if 0 you stay at the current value. If the reset input is 1 the count returns to 0, if 0 it has no effect. If both step and reset are 1, reset takes precedence. Use J-K flip flops in your design and follow the design process...

a) Draw and label your own circuit diagram using standard schematic symbols for a circuit with...

a) Draw and label your own circuit diagram using standard schematic symbols for a circuit with a 12 V battery, a 15 ohm resistor, a 400 mH inductor, and a switch, all in series. b) Write a diffferential equation (in the form of a loop equation) describing the behavior of this circuit after the switch is closed. c) The switch is first closed at time t = 0. Write down an equation for current in the circuit as a function...

Design a 5-bit binary counter using JK flip flops. Draw the flip-flop circuit diagram, the state...

Design a 5-bit binary counter using JK flip flops. Draw the flip-flop circuit diagram, the state graph, the timing diagram, the truth table (with clk pulse) and the state table (with present and next states).

Design a RAM circuit such that using two 64x16b RAM chips constructs a 128x16b effective size...

Design a RAM circuit such that using two 64x16b RAM chips constructs a 128x16b effective size memory circuit. Use the MSB of the address lines as the enable line. (Note: you will need to determine the number of address lines needed.)

Subjects