Using known op amp configurations, design and draw an op amp circuit to convert Farenheit to...

Using known op amp configurations, design and draw an op amp circuit to convert Farenheit to Celcius. C=5/9(F-32)

Expert Solution

We will use Three Inverting Op-Amps with constant input signal of 9.7 Volts and a Fahrenheit input voltage signal V_F. The circuit is as shown below.

(Note we are not using any 100 volts for 100 degree input for Fahrenheit Input voltage (High Voltages) nor we are getting 32 Volts at output. We are making it more in practical way)

i.e we can use Divide by 10 Multiplier to get V_F and x10 for displaying the value of temperature in Celsius

Manojponduru answered 1 year ago

Design a circuit using Op amp that will combine four voltages according to the following ratio....

Design a circuit using Op amp that will combine four voltages according to the following ratio. You can only use invertor amplifier . All input voltages are positive and you cannot tamper with the sources Vo = 4V1 - V2 - 8V3 - 2V4

A. Draw an op-amp circuit that will act as a comparator. Label the reference node, the...

A. Draw an op-amp circuit that will act as a comparator. Label the reference node, the input voltages and the output voltage. B. Draw an op-amp circuit with an output voltage that is the integral of an input voltage over time. Label the reference node, the input voltage and the output voltage. C. Explain what happens when a current-carrying wire moves through a static magnetic field. INCLUDE A DETAILED SKETCH. D. Give a brief explanation of how a DC armature-controlled...

Determine the gain of the op-amp circuit in Fig. E4.2.

Design and build an 8 bit Digital to Analog Converter using the LM741 OP Amp in...

Design and build an 8 bit Digital to Analog Converter using the LM741 OP Amp in Multisim software. Analyze the system using 1000 1000, 1111 1110, and other four different byte values.

Design and build am 8bit DAC using the LM741 OP Amp. Select your resistor values to...

Design and build am 8bit DAC using the LM741 OP Amp. Select your resistor values to allow typical current levels into the OP Amp. Analyze the system using five different byte values. The following byte values must be included, 1000 1000, and 1111 1110. Show your work. Use all your knowledge gain while studying under the CET degree,

Using a general Op-Amp 741, design a first order and a second-order low-pass filter with cut...

Using a general Op-Amp 741, design a first order and a second-order low-pass filter with cut off frequent of 5kHz. Subject sinusoidal inputs with frequency from 1kHz to 10kHz and plot the frequency responses for both the filters and provide your opinion.

Describe the conditions under which an op-amp circuit will oscillate. Provide a technique to avoid undesirable...

Describe the conditions under which an op-amp circuit will oscillate. Provide a technique to avoid undesirable oscillation. Explain why the gain-bandwidth product (GBW) is limited for any amplifier, and why GBW is constant for a fully compensated voltage feedback op-amp. If a fully compensated op-amp has GBW = 4 MHz, and its closed-loop amplifier circuit has gain (closed-loop gain) = 100, what is the loop gain at 100 Hz?

Create an Op AMP based circuit that converts a 2 Vpp 350 Hz Square wave (Vin)...

Create an Op AMP based circuit that converts a 2 Vpp 350 Hz Square wave (Vin) into a 4 Vpp 350 Hz Sine Wave (Vout) that is in phase with the square wave. Show this using Multisim (please attach multisim picture).

Q) design and analyze a current limited series voltage regulator that includes op amp and 8V...

Q) design and analyze a current limited series voltage regulator that includes op amp and 8V zener diode . The regulated output voltage should be 40V and the output current should be limited to 800mA . The zener current should be 9mA when Vi = 35V. (solve neatly)

3. Design and draw a circuit using the cascade system to operate two cylinders (A and...

3. Design and draw a circuit using the cascade system to operate two cylinders (A and B) which, on the operation of a start valve, produces the sequence A – B + B – A+. The cylinders should park in the positions B – A + when the start switch is in the ‘off’ position. 4. Modify the circuit designed for question 3 to provide an emergency stop which will park both cylinders in the extended position (i.e. A +...

Question