A type K thermocouple with a 0°C reference will monitor an oven temperature at about 300°C....

A type K thermocouple with a 0°C reference will monitor an oven temperature at about 300°C. Vout was solved to equal 12.209mV. But part 2 I need help with.

Part 2 asks: Extension wires of 1000ft length and 0.01ohms/ft will be used to connect to the measurement site. Determine the minimum voltage measured input impedance if the error is to be within 0.2%?
The answer given is: 9.98kohms

Expert Solution

Manojponduru answered 2 years ago

I wish to use a B-type thermocouple to measure a temperature of 16000C. I am using...

I wish to use a B-type thermocouple to measure a temperature of 16000C. I am using 1000C (boiling water) as my reference temperature. What is the emf expected at 16000C ? (Refer to the NIST thermocouple database): a) 11.233 mv b. 0.033 mV c. 11.263 mV d. None of the above

A thermocouple (TC) reads a temperature of 180 degrees C when placed in a large wind...

A thermocouple (TC) reads a temperature of 180 degrees C when placed in a large wind tunnel. The thermocouple is exposed to convection and radiation heat transfer. The convection heat transfer coefficient h = 125 W/m2-K. As for radiation, the surface of the thermocouple is diffuse and gray with an emissivity of 0.6. The walls of the wind tunnel are at a uniform temperature of 450 degrees C. Questions: Provide a sketch State your assumptions Calculate the temperature of the...

Briefly explain the significance of the Kelvin scale for temperature. What is special about 0 K?

A Carnot heat engine operates between temperature levels of 600 K and 300 K with 8...

A Carnot heat engine operates between temperature levels of 600 K and 300 K with 8 MW heat transferred in the boiler. It drives a compressor, which compresses steam from 200 kPa, 200°C to 1 MPa, 500°C. If mass flow rate of the steam is 5 kg/s. determine the following: (a) The power output of the heat engine (kW). (b) The power input of the compressor (kW). (c) The efficiency of the compressor.

30.0g of copper pellets are removed from a 300°C oven and immediately dropped into 110mL of...

30.0g of copper pellets are removed from a 300°C oven and immediately dropped into 110mL of water at 24.0°C in an insulated cup. What will the new temperature be? Please provide full solutions.

A 100-ohm resistor is held at a constant temperature of 300 K. A current of 10...

A 100-ohm resistor is held at a constant temperature of 300 K. A current of 10 amperes is passed through the resistor for 300 sec. a) What is the change in the internal energy of the universe? b) What is the change in the Helmholtz free-energy of the universe?

27.0 g of copper pellets are removed from a 300?C oven and immediately dropped into 90.0...

27.0 g of copper pellets are removed from a 300?C oven and immediately dropped into 90.0 mL of water at 22.0 ?C in an insulated cup. What will the new water temperature be? Express your answer with the appropriate units.

25.0 g of copper pellets are removed from a 300∘C oven and immediately dropped into 120...

25.0 g of copper pellets are removed from a 300∘C oven and immediately dropped into 120 mL of water at 18.0 ∘C in an insulated cup. 1.)What will the new water temperature be?(in Celsius

26.0 g of copper pellets are removed from a 300∘C oven and immediately dropped into 120...

26.0 g of copper pellets are removed from a 300∘C oven and immediately dropped into 120 mL of water at 23.0 ∘C in an insulated cup. What will the new temperature be?

If an aluminum oxide at room temperature (25°C) is placed on hot oven where it's surface...

If an aluminum oxide at room temperature (25°C) is placed on hot oven where it's surface is heated to 100°C at time t=0, how long would it take for the material to reach 80°C, 1 mm from the surface? Thermal diffusivity of the aluminum oxide is 11 cm²/s. The answer should be in milliseconds. Hint: Apply the Fick's second law. SUBMIT YOUR SOLUTION! material science course

Question