I wish to use a B-type thermocouple to measure a temperature of 16000C. I am using...

I wish to use a B-type thermocouple to measure a temperature of 1600⁰C. I am using 100⁰C (boiling water) as my reference temperature. What is the emf expected at 1600⁰C ? (Refer to the NIST thermocouple database):

a)

11.233 mv

b.

0.033 mV

c.

11.263 mV

d.

None of the above

Expert Solution

Using NIST thermocouple database,

The emf of B-type thermocouple at 1600°C is 11.263 mV.

The below table is the B- type thermocouple database.

samet mamat answered 2 years ago

A thermocouple is used to measure a known temperature of 25oC. A set of measurements is...

A thermocouple is used to measure a known temperature of 25oC. A set of measurements is taken. 29.6% of the measurements are found within ±1 oC of 25oC (the sample mean value is 25oC). We assume the temperature to be a random variable following a Gaussian distribution function. Please answer the below questions and upload your work as a single file (preferably PDF or jpeg). You need to show ALL work. Question 1. Show that the standard deviation of the...

Question 3 A sheathed thermocouple is placed in a combustion chamber to measure the temperature of...

Question 3 A sheathed thermocouple is placed in a combustion chamber to measure the temperature of the gases at a certain point in the process. The thermocouple reading is 1110K and the inside wall temperature was measured at 1008K. The thermocouple has a surface area of 10 mm2 . (a) A pitot probe is used to measure the velocity of the gas stream in the vicinity of the thermocouple tip. It measures a difference in static and dynamic pressure of...

A type K thermocouple with a 0°C reference will monitor an oven temperature at about 300°C....

A type K thermocouple with a 0°C reference will monitor an oven temperature at about 300°C. Vout was solved to equal 12.209mV. But part 2 I need help with. Part 2 asks: Extension wires of 1000ft length and 0.01ohms/ft will be used to connect to the measurement site. Determine the minimum voltage measured input impedance if the error is to be within 0.2%? The answer given is: 9.98kohms

I am quantitating lead in a solution using anodic stripping Voltammetry. I am asked to use...

I am quantitating lead in a solution using anodic stripping Voltammetry. I am asked to use the Reagents as follows: 0.1 M KNO3 /50 mM HNO3 containing an unkown concentration of lead. For the purposes of preparing the method of standard additions, I am to assume the concentration in the container to be 1ppm. 0.1 M KNO3/50 mM HNO3 (take only what needed) 500 ppm Hg ^2+ in 0.1 M KNO3/50 mM HNO3 1000 ppm Pb and the preparation of...

I am so lost on this. I am making a B in this class but I...

I am so lost on this. I am making a B in this class but I can not seem to get this project completed. Please help. ACC-120 Project – Financial Accounting This assignment supports the following outcomes: · Prepare journal and ledger entries for a service or merchandising business. · Prepare year-end statements for a service or merchandising business. · Report cost decisions using accounting principles and financial statement analysis. · Evaluate how knowledge, skills, and attitudes learned in this...

I am using a course that requires me to use excel.I am able to figure everything...

I am using a course that requires me to use excel.I am able to figure everything out except the test statistic A marine biologist claims that the mean length of mature female pink seaperch is different in fall and winter. A sample of 15 mature female pink seaperch collected in fall has a mean length of 108 millimeters and a standard deviation of 15 millimeters. A sample of 8 mature female pink seaperch collected in winter has a mean length...

For International Business. I am using Microsoft Word to type this, but you do not have...

For International Business. I am using Microsoft Word to type this, but you do not have to. 1. Create a 3-page (or more) essay on why foreign direct investment (FDI) is important; What are the pros? The cons? The impact?

I am trying to make a temperature warning system in LabVIEW. given temperature T, I want...

I am trying to make a temperature warning system in LabVIEW. given temperature T, I want a green light to turn on when temperature is less than 75 degrees. when the temperature is between 75 and 90 degrees, i want a yellow light to turn on. when the temperature is greater than 90 degrees, I want a red light indicator to turn on. how would this case structure look like in LabVIEW?

I am new to socket programming and I wish to know what these lines of code...

I am new to socket programming and I wish to know what these lines of code do. I know they are creating UDP sockets, but it would help if someone explained what the code means. Thank you. Python Code: import socket testingSocket = socket.socket(socket.AF_INET, socket.SOCK_DGRAM) testingSocket.setsockopt(socket.SOL_SOCKET, socket.SO_REUSEADDR, testingSocket.setsockopt(socket.SOL_SOCKET, socket.SO_BROADCAST, 1) testingSocket.bind(('0.0.0.0', 50000)) send_socket = socket.socket(socket.AF_INET, socket.SOCK_DGRAM) send_socket.setsockopt(socket.SOL_SOCKET, socket.SO_BROADCAST, 1) receiving_thread = Thread(target=self.receivingFunction) send_thread = Thread(target=self.sendMessage) broadcast_online_status_thread = Thread(target=onlineStatus)

1. I am trying to determine the level of measurement of my data type? I am...

1. I am trying to determine the level of measurement of my data type? I am looking for advice on Nominal, Ordinal, Interval, and Ratio 2. Does the data set have any categorical variables? I am trying to Describe the data set below in very general terms? This data consist of 8 variables: Which are GRE Scores, TOEFL Scores, University Rating, Statement of Purpose, Letter of Recommendation Strength, Undergraduate GPA, . Research Experience, and Chance of Admit. Name Type Description...

Question